Search results

Guys I’m looking at an arb locker for the front of a Dana 30. It would be 355 gears my question is what’s the difference between the one with 355 and lower gears and the one with 373 and higher? 10 years from now would I need to buy another locker if I upgrade to higher gears for bigger tires or...

Guys my Jeep is a 4.0 aw4 transmission. I’m trying to diagnose an issue. So driving down the highway cruising in overdrive everything is fine but when I start going up a hill and I put my foot down and it downshifts the Jeep starts surging. What could cause this? Driving around town everything...

Hey y’all haven’t been back on here in a long time my jeepers been running good until I changed my oil.. I went with castrol 5w-30 and I’ve been driving it back and forth from work for about a week. Then coming home from work I noticed oil is pouring out of the slot in the bell housing. I...

Guys I’m just curious couldn’t find much on this. If I installed a locker and a few years go by and I want to run a larger tire or have more pulling power can I regear and run the same locker? And is it the same on a limited slip?

Guys how the heck do you remove the knob for the transfer case?

Guys I’m wondering if they make a metal window crank handle that will work for a 97 Jeep Cherokee. I keep breaking these plastic ones.

Guys I was wondering if any of you are running a ford 8.8 rear axle with the Trac lok and carbon fiber discs? If so how are they holding up?

Just wanted to post that they still make the old harness for the blower speed switch. Found one. Santech ac components: part number MT1670 Incase someone has one that is burnt up like mine was.

Guys I carry quite a bit of tools in the back of my xj. On these old leaf springs. Is there a way I can add a leaf or would I have to buy new stiff springs?

Guys is the jk Dana 44 the same length as the xj axles?

Guys the ones who have installed a truetrac in there Dana 30 what do you think of it.

Well guys I’m needing some advice. So I just replaced all my tie rod joints. And it made the wobble a lot better but it’s still there sometimes. The ball joints are in good shape. I took a tape measure to the tires and got the alignment close. Don’t want to pay the money to align it until I know...

Guys I’m literally stumped. I’ve had my motor apart 5 times replaced everything on my cooling system. New fan clutch new auxiliary fan. Wired it to a toggle switch. New 180 degree thermostat. New cylinder head. New 2 row radiator. Installed a mechanical temperature guage to I can actually read...

Guys what would cause the steering to wobble only on acceleration? I installed a Jeep zj steering on it.

Guys wanted to see what your thoughts are if you have used these heads or not and how well they are built?

Guys I’m stomped. I have replaced my thermostat water pump radiator hose and head gasket new auxiliary fan. And the damn thing is still overheating …

Guys I am working on my ac trying to get it to work on my 96 xj and the compressor will kick on somewhat if I pull the relay and reinstall it. But won’t stay turning. It probably hasn’t been used in years. The compressor acts somewhat locked up. Is there anything I can do that could help get it...

Guys I had to replace my heater core awhile back and somehow I missed a piece of ductwork and now I tore it back apart to install it. But I can’t figure out where it goes was gonna see if you all could point me in the right direction. Here is a picture

Guys I’m curious if any of the zj rear Dana 44s where iron and not aluminum. I took a magnet and it stuck everywhere on it. It had a 5.2 motor.

Guys I’m trying to figure out why my fan isn’t working. I checked the fuse and I have power at the relay. Switched relays and still no power to the fan. Checked the temp sensor and it was ohming out. The engine Was still hot when checking these things. What I am wondering is the harness that is...