Search results

I have a TNT customs trackbar setup for a XJ with 4"-6" of lift. It has been sitting in the garage collecting dust and could go to a new home. I would rather not ship but we could work something out if it's not too terrible. Make me an offer I'd like it gone pics to follow soon

I'm looking to sell a bunch of stuff I have laying around from the old XJ 32x11.50 BFG MT on a soft 8 steelie 3.75 BS never on the jeep Currie steering one TRE boot has a rip in it 4.5 inch RE front springs Teraflex 1.5" shackles JCR stage 2 Sliders TJ Flares trimmed And some more stuff that...

Let me know what you want if it is not listed. I will post pics if requested. I'm getting rid of my XJ, and the story is as follows. The tranny has been acting up and it been causing the heep to overheat. It's also having trouble with the NSS it will start but only by me getting under it and...

So i'm gettin rid of the XJ and there is a bunch more stuff to come. But first my dana 44 has to go. I bought this thing years ago and never got around to putting it in. So here are the specs for it. It's a stock XJ 44, open carrier 4.56 gears, tubes are welded, it's trussed, ruffstuff cover...

Has anyone replaced the heim joint on the sway bar link and what size is it. I've got the thing soaking right now to try to disassemble but want to order the heim through mcmaster cause they are quick cheap and fast. Any help would be good and I'll update the thread with a part that works if I...

I've had my dana 44 apart for way to long and I forgot what side the longer shaft goes into. I've searched around but can't find it now go figure. Any help would be great thanks in advance

I"m getting ready to put my axle in and really want to splurge on some nice stiff shocks. I'm leaning towards the 5150's for the rear right now. Has anyone had any clearance issues with them due to the remote reservoir? The shock mounts are raised up but stay around the same position. Would I be...

Title says it all I'm looking for a D30 to try to build up so I don't have to have the heep down when I regear. I have D44 that just got it's new 4.56's in it and I want to truss the turdy before it goes to the gear guy. I'm willing to drive but it seems like only MA people give away turdys

I've had an XJ D44 sitting in my driveway for a while and decided to get on it. I trussed it raised the shock mounts and dropped it off to get gears put in it. I was wondering if I could bolt it into my heep when I get it back without doing anymore mods. As of right now I don't have a SYE and I...

I was onyl able to make it out there on thursday, it was fun having the whole park to ourselves. Thanks to everyone for making it a great day it was nice to get my mind off of things. I have more pics so if anyone wants them PM me and I will e-mail them to you click to make em bigger

My specs are in my sig. I'm having a small issue that has just come up. My jeep when first started will hesitate for about 2 seconds sometimes pop from the header and then run fine. It does that more often than not. Now only 2 times when it is sitting it is idling really bad and it will surge up...

So I just threw some 33's on. I wanted to do 35's but I like the skinny pedal and I need more axle to run them so I settled. Here are some pics from the local spot to set some new bumpstops and check out the new currie steering and whatnot. One question I have is I'm trimmed to the pinchwelds in...

I have no brake lights working on my heep right now. THe brake switch isn't sticking and it seems like I don't have any voltage at the sockets. Where else can I check and is there a fuse I could pull? Any help would be great

I just installed the currie steering on my 98 XJ. It all went very smooth and it went on great. Now I have a clunk in the front end only when I brake kinda hard. All of the bolts ae torqued to spec(55ftlbs), and the adjusters are tight. There is also no steering stabilser on. I'm wondering if it...

I have a RE1600 trackbar with a heim joint that is gettin loose. The bar is in good shape as well as the axle side bushing it is about a year and a half old, but like I said it probably will need a new joint soon. I'm looking to get $70 for it. I will have pics up soon and I'm open to offers

I have a RE1600 trackbar with a heim joint that is gettin loose. The bar is in good shape as well as the axle side bushing it is about a year and a half old, but like I said it probably will need a new joint soon. I'm looking to get $70 for it. I will have pics up soon and I'm open to offers

I just got finished installing my TNT trackbar and it seems a little off. It looks like the the joint where is meets the body mount is resting against the mount. It seems like it would limit travel and its just not right. I have the RE 4.5 kit with fixed uppers and lowers. I think that if I move...

Title says it all I am looking for a ax15 in good working order pm me if you have one or can get one thanks in advance

Is there anyone in northern NJ that has some 35's that I could do a test fit cause my tires are beat right now. I'm trying to decide between 33's and 35's and I was hoping to throw one in the front and check for clearance before I go out and spend the $$$. Steering and axle upgrades are coming...

The title says it all I have a rear tow hook bracket with hook and homemade nutstrips. You will need to modify the opening where the nutstrip goes into the frame as this thing is beefy. Everything in the pics are included and I'm asking 40 OBO plus shipping the thing is heavy and local pick up...