Search results

Hey guys, i have some 37's that need a home. There is some tread left on them and they really evenly worn. http://reno.craigslist.org/wto/5286348151.html Bryan

Hey guys...its a sad day but I am going to sell my jeep. Those of you who have wheeled with me...know its well built and well taken care of. here is a basic rundown of what its got: Dana 44s F&R, 5.13s, ARBs, Superior Discovery Chromo shafts, 37s, etc. See my craigslist ad...listed at $8500...

Hey guys, anyone have a transmission oil pan for a AW4 (mid 90s, not sure it matters though) laying around that they wouldn't mind parting with? Thanks! Bryan

Hey guys, so I tore out all the a/c stuff on my 95. It is used on the trail mostly with half doors so I wanted to clean up the engine compartment and try to improve some air flow. Now that the a/c compressor is gone, the auxiliary fan no longer comes on with engine temp. I have it wired up with...

Ive got one Chrysler 8.25 29 Spline Yukon Brand Shaft for sale. This would make a good spare...the splines are slightly twisted, you can see it in the picture...$50 Pics

I would like to see if there is any interest in my XJ Dana 44 rear axle. It has 4.88s with a stock LSD rebuilt about 4 years ago, Crown Vic Disc brakes, raised shock mounts, stock "heavy duty" front dana 44 diff cover from a front axle, it is 3/16"ish thick...I would be looking to get $650 or...

For sale- New in the box Yukon Spool for a Dana 44, 30 spline, 3.92+...part number YP FSD44-4-30UP Not a whole lot to see, but here a few pics- Looking to get $130 shipped Thanks- Bryan

Well I did it...went red! I got a real nice Sierra Chapter Naxja Sticker last year and I just couldnt justify putting it on the jeep without it being official. Plus, Naxja has been a great resource over the years, I dont think my jeep would be where it is today without Naxja. I have meet a...

Well, the rust on the floors of my jeep that I bought when I lived in Chicago finally caught up with me! EricsXJ and I were out wheeling a new trail right near Reno and on the way home after a few hours of wheeling, then airing up, then driving...I started to smell something burning. At first...

So I decided while I have the jeep apart for dana 44 swap, I would make some front frame stiffeners. I have read all the threads about them and tried to incorporate some of the ideas mentioned about providing more stiffening. So I left them a little long on the bottom side and "wrapped" them...

While my Jeep is on jack stands with my HP44 getting its ARB installed, I thought I would pay some attention to the rear XJ44 that I built a few years back. The axle seals had started to leak and I had never hooked up the e-brake with my crown vic disk set up. So...I decided to get some new...

Rubicon Express Control Arm Drop brackets They are in good condition, have a little rock rash, and a few spots that were cleaned up where they were tack welded to the jeep, but other than that they are good! $200 for the brackets and supports. Located in Reno, would prefer not to ship, but...

Anyone have any door hinges (door side only) from a 96 or earlier? Thanks- Bryan

Finally finished up the conversion of my front bumper to hold a winch...Kinda like EricsXJ. And you can see in the pic I also finished my WJ knuckle/brake swap. The WJ swap went really good, I had WFO concepts make up some 1.25" x.219 wall tierod and draglink and used chevy 3/4ton tre's and DL...

Decided that my old front bumper provided about zero protection for the front corners, so I hacked it off and reconstructed the ends...much better now and protects the corners. Before: After: Also I decided to ditch the fender flares. After rubbing a rear one and pushing in some sheet metal...

I have posted these before and got too busy to follow up on some leads, just seeing if anyone around here may still be interested: Both sets are stock axle shafts. 1. Dana 30 stock 297 shafts, good spicer 297x ujoint, used as spares....$75 2. Dana 30 stock 297 shafts w/ unit bearings( about...

I have some things that I need to get rid of: -4 Stock XJ wheels, decent shape: $50 -Stock Rear Driveshaft: $10 -Stock Front and Rear Bumpers(front has been cut at 45' on ends): $10 for both -Stock Tail Lights L and R (no cracks): $20 -Rustys Chrysler 8.25 Diff Guard (almost new condition, no...

Well I did the swap yesterday, everything turned out great. Followed "Jeepin Jason's" write up on NAXJA and it turned out great. I only replaced the high pressure line and return line not the whole pump. Used the C-rok inner plate with some .25" washers(from an old set of u-bolts). Everything...

Those that have used the extra v-belt pulley from Kilby or 4x4rockshop (i think they are the same)- Is the back side of the pulley mostly flat with a small raised flange that seats against the alt. ? I want to make sure I get the right pulley for my alt., b/c I was stupid and made one from xj...

Trying to get the old pulley off my 95 to put on my combo vbelt/serpt. pulley for my York. It has a 10mm bolt end on the shaft and a 22mm nut holding the pulley on. I cant get it off for the life of me. Anyone have any tricks to loosen the nut? Thanks