Recent content by xjklmnop69

I got a OBD scan tool that would to ABS. Found three fault codes, LR and RR wheel sensor open circuits then ABS Pump circuit fault (09). I found the old rear wheel speed sensors from the D35 and plugged them in hoping the pump error would also clear but it didn't. Wasn't able to successfully run...

I borrowed a vacuum bleeder setup. Tried a few different bleed methods with little improvement. Initially I started at the furthest corner and worked forward just trying to maintain vacuum with the bleeder open. Next I found and read the mityvac recommended way of starting at the closest bleeder...

Did the booster have an internal leak or vacuum supply? I was considering the booster also, so I disconnected the vacuum supply from the intake manifold. My pedal felt stiff but was ineffective at stopping. When I swapped over to the disc I went to install the Liberty prop valve internals but...

I had one of those while you are in theres during this brake job and welded some material back to the steering knuckle where the front pads slide. The pads were starting to get a taper. Regreased all the slide pins and boots too. Once I get this hydraulic issue figure out its going to be like a...

Thanks for your suggestions! Replumbing all those lines does not sound fun so I'm trying to avoid that until its the last option. I did watch the hoses as the brakes are pumped and I didn't see anything swelling up. Opps.. Forgot to mention since its been in there so long but good point. It...

99 XJ Jeeps been sitting all summer as I've replaced floor pans and rock sliders. Came back to her with no brakes Pedal goes to the floor with minimal resistance, brakes were never excellent before but they'd hold enough to spin the rear tires A few years ago I did the Liberty rear disc swap...

1999 Cherokee AW4 ~300K So I was in some real wet terrain and my the lower end of my xj was pretty wet. Water lines look like the alternator was submerged. My voltage gauge maxed out and then all the gauges died. Volts, fuel level, oil pressure, and water temp all went to the low end then the...

I took a hiatus from the garage over winter. I couldn't get myself to go out there if I didn't have to. Too cold.. 2000 miles later she has stayed wobble free. I left it on the 2" coil spacer 3" spring up front. Rear was lowered on an adjustable shackle to level out with the front. Its been...

I swapped out the 3" coil spacer with the 2", adjusted the track bar, set the toe (~3/16" in) measured caster (D ~8, P ~9), pinion angle = 3 up. I took it for a spin and wobbled just like when I had the 3" spacer in. I then widened the toe up an entire spin to see how it would go. Eye balling...

Thanks for the input everybody! Didn't make it back out the next day as originally planned. -Had someone turn the wheel while I felt and looked for loose components. Still nothing seemed to have any play. -Certain bumps used to give me a bit of bump steer. Felt like the back end would skip...

According to the alignment sheet, I have 7.8 and 7.7 degrees of caster. I threw an angle finder on the top ball joint and got ~8. The setup work for fine on these same bumps for 8-10k Initially I thought I threw a wheel weight during the wash but wheels were still in balanced. I swapped wheels...

I did many searches with no ultimate luck 99' XJ with 6" lift. Dana 30 high pinion. Lift is made up of 3" springs and 3" spacers, fixed tubular lower control arms, OG uppers, rubicon express adjustable track bar with bracket/brace. I had a weekend in the sand dunes then drove home about 300...

Finished up the install the other week. Driver's side did not have any wiring other than the door chime. Jumped the power off the passenger side and ran it over to the driver. Power adjustments on constant power Heated seats on ignition power

I didn't even think about the chime wires. Mine happened to be missing them on the passenger side. I checked the drivers side to compare; it is also a two pin connector but is much smaller than the wires in question Fuse # 29 feeds the big red wire which is constant 12v. Then fuse #18 feeds the...

Awhile back I swapped in some WJ front seats into the XJ but now I'm finally coming back and trying to hook up power to the motors and I added heated seat pads under the leather ;) The Cherokee in is a luxury stay now I pulled up the passenger side carpet to run wires from the underdash fuse...