• Welcome to the new NAXJA Forum! If your password does not work, please use "Forgot your password?" link on the log-in page. Please feel free to reach out to [email protected] if we can provide any assistance.

Recent content by Roll-over

  1. R

    help with a '90 renix...

    5-90 gets the kudos on this one... One of the wires from the CSS (Crank Speed Sensor according to borg-warner) to the harness connector is freyed enough to ground out to the intake. Thanks All for the help. I'll wrench on it tomorrow and post results.
  2. R

    help with a '90 renix...

    I can practically guarantee its not the block strap. I replaced that last fall, as well as added a strap from the battery groung to the inside fender panel. While I was in there I also vamped the grounds to the tps and air-bypass stepper and screwed them to the block. All the attachment points...
  3. R

    help with a '90 renix...

    thanks, 5-90. I was kinda hoping you'd see this. -r0
  4. R

    help with a '90 renix...

    here's the deal, a couple days ago the jeep start sputtering and bucking on the way home from a client's site. It's hard to start, sounds like the timing is off (or fuel starved), once it "catches" it's fine until i get it moving then it starts surging - bucking - stalling again. It's a 1990 4.0...
  5. R

    Resume help...

    The short answer is any market. the position is Geek. I thought about doing the multimedia business card cd, but that seems like the resume of someone with too much free time. Rckclmbr, PM sent. John
  6. R

    Resume help...

    I'm thinking about fishing the job market a little. The problem is my resume hasn't had a face-lift in about 3 years. Would anyone be willing to have a look at it and give me some constructive criticism??? Let me know and I'll post it in doc format. John
  7. R

    TEXAS - Padre Island 6/16 thru 6/19

    OK... in case anyone's interested, here is the info ! I'll be leaving SA about 5am on the 16th as I have some business in Corpus. I plan to register at the park HQ by 11am and get some fishing and wheeling started. As there is atleast one 4x2 going, we'll meet up at the Maliquite beach visitor...
  8. R

    TEXAS - Padre Island 6/16 thru 6/19

    Driving conditions are a day-to-day thing... The general rule is 4wd only after 5 miles or so. The last time I went down there the tide had just gone out and it was like a gravel road. The time before that it was like quick sand after about 5-6 miles. So far there are three confirmed rigs on the...
  9. R

    TEXAS - Padre Island 6/16 thru 6/19

    Corpus area. We're taking S.P.I.D. down to Malaquite Beach and then 25 miles south to "Big Shell". You could take 100 (Queen Isabella)onto the island and then come up I guess... :dunno:
  10. R

    TEXAS - Padre Island 6/16 thru 6/19

    For fathers day some friends and I are heading down to PINS for some surf fishing! Anyone interested in joining? The area we are planning on fishing is about 25 miles of loose sand and eroded surf from the park headquarters. At around 50 miles down are a couple of ship wreck sites. Fishables in...
  11. R

    Reserve fuel tank?

    I have a 90 with the same specs... the tank capacity is 25 us gallon (20-22 fuel depending on pump speed + 3-5 vapor space) the vapor space is maintained by the filler breather tube which can be bent (Gojeep wrote the tech on it!)up to increase the capacity. the odo and trip odo are mechanical...
  12. R

    Tool Brand Question

    ROCK ON!!!
  13. R

    Drill bit & tap size for sye?

    The Ace - True Value in my area has all the goofy sized bits in their tap section with the taps they go to. Just for reference... Also, I've found using a 1/4" or 3/8" drive impact to cut the threads works well without too much effort.
  14. R

    What Gives? Wrong Tie Rod End.

    if you go to autozone it's the right-inside TRE... It sounded backwards to me, but I got the right part.
  15. R

    Door handle source question

    (accidental repost, sorry)
Back
Top