NAXJA Forums -::- North American XJ Association  

Go Back   NAXJA Forums -::- North American XJ Association > NAXJA Unibody Jeep Technical Forums > Jeep Cherokee XJ (1984 - 2001) > Modified Tech Discussion
HOME Member FAQ Sponsor Info Rules Bylaws E-Mail

Modified Tech Discussion Forum for Tech related discussion for Modified XJ's and MJ's.

Reply
 
Thread Tools Display Modes
  #1  
Old December 6th, 2019, 15:29
Jeepmedic46's Avatar
Jeepmedic46 Jeepmedic46 is offline
NAXJA Member
 
Join Date: Nov 2019
Location: Orange, Ma
Posts: 55
Azzy’s design linkage

I was wondering if anyone has used the Azzy’s design linkage on their transfer case. My 2000 XJ transfer case linkage is broken and not able to find a replacement. It is a NP 231 Transfer case and the Jeep has a 4.5 Rough Country short arm lift.
Reply With Quote
  #2  
Old December 6th, 2019, 15:41
JohnX's Avatar
JohnX JohnX is offline
Sarge <3 Ben
 
Join Date: Nov 2004
Location: Rancho Cucamonga CA
Posts: 9,726
Re: Azzy’s design linkage

I have it on my 98. Wasn't impressed. It took me several tries to get it to work 1st of all, and then it bound up several times on the trail. I had trouble shifting back to 2 wheel drive. I would not buy it again.

If I were to do it over, I would look for a cable actuated shifter. Not that I think it had anything to do with bad trans mounts motor mount, my engine and trans was stable.
__________________
The MAC-10 submachine gun was practically designed for housewives.
Reply With Quote
  #3  
Old December 6th, 2019, 15:42
cal's Avatar
cal cal is offline
NAXJA Warranty Voider
 
Join Date: Nov 2004
Location: Hammertown, USA
Posts: 17,559
Re: Azzy’s design linkage

I've installed the boostwerks one a couple of times with good luck.
__________________
I'm not a complete idiot - there are parts missing.
Reply With Quote
  #4  
Old December 6th, 2019, 15:51
smokeyyank's Avatar
smokeyyank smokeyyank is offline
Jeepoholic
 
Join Date: Jul 2014
Location: Gypsum, Crawlarado
Posts: 1,022
Re: Azzy’s design linkage

Was just chatting about this on comancheclub. Between that and the Boostwerks they are the same really. The Azzys has some "graphics" and a high price tag.
__________________
88 MJ truggy, 4.0HOybrid AX15, NP242 **Being built**
Mods: D44 w/ 4.30's, ARB front and Auburn rear, 33's
04 WJ, 4.7HO
Mods; 3" IRO lift, ADDCO rear sway bar, 4.7HO with bored fastman TB, AFE intake and Superchip tuner, 32s, lunchbox rear 242HD, 3" Kolak exhaust
Reply With Quote
  #5  
Old December 6th, 2019, 16:03
Jeepmedic46's Avatar
Jeepmedic46 Jeepmedic46 is offline
NAXJA Member
 
Join Date: Nov 2019
Location: Orange, Ma
Posts: 55
Re: Azzy’s design linkage

If I was going to go with a cable one which one would be a good one? I thought I saw on the Quadratec site they had one similar to the factory one.
Reply With Quote
  #6  
Old December 6th, 2019, 16:27
denverd1 denverd1 is offline
NAXJA Forum User
 
Join Date: Dec 2013
Location: Tyler, TX
Posts: 864
Azzy’s design linkage

Got Azzys on mine. Takes some adjustment to get installed correctly and some common sense when setting it up. Works great

Sent from my SM-G975U using Tapatalk
Reply With Quote
  #7  
Old December 6th, 2019, 17:32
Jeepmedic46's Avatar
Jeepmedic46 Jeepmedic46 is offline
NAXJA Member
 
Join Date: Nov 2019
Location: Orange, Ma
Posts: 55
Re: Azzy’s design linkage

I think I’ll go with the Azzy’s. I’ll have to try and find a place to install it. I can’t be on my back due to surgeries.
Reply With Quote
  #8  
Old December 6th, 2019, 21:17
freggie freggie is offline
NAXJA Forum User
 
Join Date: Feb 2018
Location: CA
Posts: 17
Re: Azzy’s design linkage

Have it installed, install was not bad but getting dirt in eyes was not fun. You can use a long screw driver instead of the pry bar and if you do not have a reciprocating saw, you can leave the oem brace thing on (I did, no problems).

The problem I had was fully understanding the directions for adjustment. I did not adjust it correctly and shifting was hard and popped out of 4lo. Carefully read the directions and it shifts butter smooth from 2hi to 4hi. Going between 4hi and 4 lo gets a little notchy but slides right in no problems.
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Azzy's Design Works XJ Gauge Inserts Renegade_Azzy Vendor Advertisements 22 May 24th, 2013 15:10
Azzy's Design Works XJ Gauge Inserts - Carbon Fiber style for 89-96 XJs and MJs Renegade_Azzy Vendor Advertisements 0 January 26th, 2013 17:50
Need graphic design help Matt S. Non-Tech / Off Topic 5 March 18th, 2010 16:03
T-Shirt design Vince 25th Anniversary Celebration! Moab, Utah 27 November 9th, 2007 19:27
LCA lenght and design Xjdubber Modified Tech Discussion 0 April 8th, 2004 17:25


All times are GMT -7. The time now is 10:58.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2020, vBulletin Solutions, Inc.
NAXJA and NAXJA logo's Copyright NAXJA. All content/images Copyright NAXJA 1999-2014