• Welcome to the new NAXJA Forum! If your password does not work, please use "Forgot your password?" link on the log-in page. Please feel free to reach out to [email protected] if we can provide any assistance.

anyone else had issue getting waterpump to seal?

Nice looking pump. I like the anodized
impeller. A lot of extra quality for just
a few more bucks.
 
Weasel said:
update, FlowKooler from Summit showed up last night. I wasn't going to spend the extra bucks but noticed that they have a machined impeller now and for $86 buck it's wasn't that bad.

Fit and casting is notically better, lots more clearance everywhere and non of the issues from the Carquest pump.
Click to expand...

Looks like a copy of a Hesco water pump, at a much lower price.
http://www.hesco.us/products/7967/h...he-high-flow-water-pump-hf58-455#.XJZmWS2ZM1I
http://www.hesco.us/shop.asp?action=showpic&id=55183&header=false
 
jbeintherockies said:
Just for reference.
Click to expand...

Should be 2, one at 12 oclock and the other at 6 oclock approximately. I can get a pick off the old pump if you would like.

lazyxj said:
Looks like a copy of a Hesco water pump, at a much lower price.
http://www.hesco.us/products/7967/h...he-high-flow-water-pump-hf58-455#.XJZmWS2ZM1I
http://www.hesco.us/shop.asp?action=showpic&id=55183&header=false
Click to expand...

Exactly my thought. I asked Hesco if theirs were rebuildable and they said no. Hard to pay that much for a pump that shot when it leaks. They could find a seal and rebuild if they felt inclined.
 
Pics of the weep holes, they are actually 12oclock and 5 oclock roughly

Top Hole
WsrfTs8ei0wvb8xP0ZX-xKAk-u5XBCIwEF_bzn6SMcaQuZHeG1BFQlbMdhBTgsAO6cXgCWnTGEzzLgtnxtySAz_BLF9bqqIJHQTwJKXo0f-IAiFjxOPWiEGiE8-jnL--B-tL-jOYnq_kyN9xvmk76gxoGuZGMkwwqjvKv8lv4mXOXTfHq3C7CvhIXS4o-BnkTID35y7LfqVycK06_KIxczIKkK23DN6tqxK5qLYGlRdg5Q2ZfpL1FzJRaTA6R-lBiu6ZlZOXCPCKhYb_tYbZLed8wveyYF_dfgkngXAcpaAfkPgI6KWcdhbgNG2Cu0muLwTiJXJfA2SXK-KuMbPjHOhHyCnmyCabTFylRaKc2y5yP_lhSuYMpE5tA43rlRcv7ZIWtTWoAqSzA383vOn8SDewEK2Jg-9-vGyJbZzP0bVZtmFZyc54Q4NQrORFAtP2Pc_v_1IUPuffWUotndzIFQwDQBa723DnvLeZdb5qGdc-vcpnRfbFG1Rn3J4lJEEojDGLZF0RKsbiu8DsQ7itjBedSk7h-90FLvOh7zOOEMAdDCyQSunp2Cy2nvDSuKOdSYpkYrIRckiaa_e4plWYkhvHNGgVCQqlq6p8wZQjFSVTRUSvwHEodmaa8Krfq9hAEYQCyHvfZw_CGfFNWY8YgHKsRMk22Nm0=w2160-h1220-no


Bottom Hole
iap6YZdgUU3BFJGVtBcOrss6akBsvnpODWfogppI6b3rcblFmtJ4AJXaHrE7KkacwyfPCBJsO4EcgeVg5KsGdrJA4o-9UTN4qr9X2ru6XZCThRWmMgEOEGoRjPRS61om897NOIf7ihP_PlVLvcs83ekD3pvvqkV6ZhqQc2FxKOZxugdnGm2ySYDBDwKNa4jITdWywnX3s70AWEPaROn0HcWHgGMZlUswOyXIzS07Sw76YQg49v6P0YGg_pov7d1YF5dyw9Ve75xcyfpCvciywmeedYWw2VqJFbuO9GoMuKaO-6e53W_MyS9AmJw2FvdJCJCECDiG-SUjgfJ92JiNhMKcHu7LAeNJWlsFf__4EQWcrlXVC4MtJX8uHvpBpT0z4PCSas-UIXvyyLfoUkkUlgg5I5DG0I-teC9r8xYm8D2Ktw92b6ltXMA6KElH-_rWzNnC60xK-RlS459hlxDZXCxsc6ak9eUOwUR-C2mZxSIv9AF2ufRSRAWimngtbZyWLP0_8fpVIBFByJX2GB7Mq4BzjLvDcqtIYeNvjF0wydkhHBYCcYbwGxSQXlpVFpnRyTKTYttTJ1lQPE7NYhHtfExSXmL2Np8nTRsqfc9ccRI3BeA5rS3P73NVpD1Ch-YADEl6S16aDuiLSc5peS7CKw9iYhbHJo49=w2160-h1143-no
 
Just a point of information for some of you. Have you ever bought a hose that has a plastic thread through the end of the hose that is used to hang up the hose. Well, that tiny hole can be a real hassle. You really need to trim the end of the hose back about a half inch to get rid of that hole. I ran into this some years back and I couldn't figure out why it kept dripping.
 
You must log in or register to reply here.

Similar threads

C
Cowl leak seems to be unreachable. solution.. Seal the hood cowl?
Replies
5
Views
2K
clean96XJ
C
1
Heater inlet pipe keep commander 5.7 sealing issue
Replies
0
Views
157
1-tonxj
1
E
95 XJ Overheated, Shop says Head Gasket, need advice/info
Replies
18
Views
3K
Etherel15
E
D
Evaporator Seal
Replies
3
Views
623
Saudade
Saudade
Anak
Gear Oil Jug Spout: I should have done this years ago
Replies
4
Views
2K
Bent
Bent
Back
Top