• NAXJA is having its 18th annual March Membership Drive!!!
    Everyone who joins or renews during March will be entered into a drawing!
    More Information - Join/Renew
  • Welcome to the new NAXJA Forum! If your password does not work, please use "Forgot your password?" link on the log-in page. Please feel free to reach out to [email protected] if we can provide any assistance.

Important

Free shipping = they do nothing I'm assuming.

They'll give you a credit. Unless it had a disclaimer that shipping would be delayed for x amount of time. I've seen prime items where it had a disclaimer like that, but they were still prime meaning once it was ready to ship, you'd have it in 2 days or less.
 
I'm liking the t19. Truck seems to have more power without the worn out c6. 10psi in third gear on gravel is fun.
I'm liking the LS rear but want my disks back. Lunchbox in DD 10.25?

Talked to Jed's friend about the cheap ECSB 250 Powerjoke, he didn't tell me a price but said "not much more than scrap". Says it has new balljoints and stuff. I may buy it eventually.
Jeep is back to standby duty, I may start putting money into it after harvest.
 
If any of you Wisconsin peeps make it over to the airshow in Oshkosh this year, you might see an ugly fat guy in a flight suit with a couple of V22's. I bet he can get you a good tour.


Bad ass. I might have to go this year. Haven't been in a few. Last time I got escorted out of the John Deere sxs ride experience for "treating it like a motocross track".

They didn't find it as funny as I did when the tail gate fell off when I failed to clear that double :)

John Deere steering wheel hurts.
 
bybeqepe.jpg


mac 'new pattern from gears on monday' gyvr
 
What are you guys running for gear oil with your lockers? I have some noise coming from my rear axle I just put under the jeep this spring... I do not have much info on the axle from the PO as he bought it built and never used it... 8.8 with an ARB and 4.88 gears... Most noise when letting off the throttle... Can't decide if its shims, oil, or if the bearings need to be replaced...
 
What are you guys running for gear oil with your lockers? I have some noise coming from my rear axle I just put under the jeep this spring... I do not have much info on the axle from the PO as he bought it built and never used it... 8.8 with an ARB and 4.88 gears... Most noise when letting off the throttle... Can't decide if its shims, oil, or if the bearings need to be replaced...


Pull it apart and look?

mac 'or have your kids do it' gyvr
 
Pull it apart and look?

mac 'or have your kids do it' gyvr

Yeah, that's the plan tomorrow, just wondering what gear oil people are using so I can grab some on the way in...

Converting the compressor an lines to 1/4" tomorrow as well...
 
I used the autozone stuff mostly cause I change it all the time when I wheel all the time.

mac 'not used long enough to matter' gyvr
 
Yeah, I'll stop by my AAP and use my discount on the store-brand... Luckily I bought shims for my old 8.8 so I should have plenty if I need to re-shim anything...

99SJ 'Hoping its not bearings' Ex
 
well i learned a few things about acetone yesterday trying to strip some paint off the black/gold jeep

1.) it does take spray paint off without damaging clear coat

2.) if you strap a t-shirt to an orbital sander it saves you some arm fatigue

3.) if you leave the opened can of acetone on top of your Jeep and it falls don't try to catch it with your face. Getting acetone in both eyes, your nose and mouth at the same time is extremely unpleasant. Fortunately I had the hose sitting right there to rinse myself off with...I think I'll wear a face shield today, or leave the can on the ground.

Alt "ouch it burns" rocker1
 
Back
Top