PDA

View Full Version : Gear pattern check


racer32
October 5th, 2017, 21:43
Anyone have an opinion on this pattern?
https://lh3.googleusercontent.com/RSRiLGglxRQhgbYDUWGsLsOo0tDE4IOO4bceuYN_RwooWdzazw sHnN-StSktTUPCve1pcvMJHnMngjdxVovWxFnZYris2cD1qoXsWlBF9 a1WwG4UXGog4TnOqW4wxTQ2jHwCdpj2Rt-XJkQAxmzb8uc5RSTmaBgCam1WYVcL_d-GBgR_Ur2R62zSMJIaRuqwEPuMa7W_F9TGD41cbFP19oAMIjEiD R1f1CQc_A03vLAILg3k71yAWOWitG6Wy6Y88gde1HKJGBF6qur 4Y0uVTba_aEGBF8VasF8IXUkWw5WvSGdpB-T1UQBQY7G0a7wGt1o2vj2xY3EtZTHY1sOIw9uPSUvfeieMqvtm i_51bTWyHIpixgCVqM1YH554Vt7Dyad5hVoy6Bexlj5HHaCjMt CMMjl6NBMaGTnt4FZZ-09Pn2QpTMngkPSE61SLgeUPE-ySN2u_Bl5XEBh3YlRy4fAtlA1tzzNaOtk5aWx2Zs1kChqpYc1o gMww31EgfLEHqaUY6bmQI-MIvSIl3axoAAe3fr3xKRTWlyDj49DVhJUCc4NEqZ8esJZCTsQn rmTNHNN2gkXrrCtTsG72dFegkMcqAcLE8yuHv2jUYscNw_o=w5 40-h959-no
https://lh3.googleusercontent.com/E5KHTUNaDQFuDq4BDmOXpJ412sUoixj3-M1JQBLIG_seUCzA3w2O6-y0RKC2II3-Vhk3FUncSsYz6v1Cc0nZAdRFn4UG7VH6WveXfMR9FdRH1LoU0l 9_3vUh28olScZisrFoCAhTAM36MB-72PuwywnXAvXn9vqJObAd2brBoRT1zmzKmuH_98W2Ss1OpsNwA YrdN7W_s_WdsgdPfyRMHNyQgJNmkCowxtC5BtIbp3Vj1MIn7Df Ajz2RdQhXGwlL_KtSZeansQ6KXW1sjaCNVLAy86g5yLAlZE53u Z2LTXwtBt_HA7e8eF9WugiFxgy1uGbL27DTBp7uRMlm5-fZEQ3JGCp5acwGzsPO7nH3vzJwON4JmLvPtKcxA8dfNSwA6Dwt 4RBGq4TBLz6nf3STaE6DAEavR8SVYpB6Mv7uZ6twIRLl1_C28V rBX1jij8sdZ8_BKxhq-aHq7hvbJU2-eQxmJuHNgrWBcE2gR3G6uqpvJV82Cla5xe2sdsbUJAYEzNebzm IEJsUy2x1jHKwbOlP3oPilcOBcbo1ljWxjwuSdGlcGAAbeGgLC aa_ZF_xxekXcDNPLhy3l_IEiOuw-Gt2L5X40no6QJY18WcgAeDs=w1705-h959-no

clydefrog
October 5th, 2017, 22:09
It looks as if your not putting tension on the pinion while running the pattern with paint. Pretty vague pattern. However I did look at it pretty close, it seems as though the pinion is 'slightly' deep. Maybe back it off a tad. Ring gear looks spot on.

I would wrap a rag around the pinion and have someone hold it to put tension on it. before doing any adjustments, and re-run the paint to see where your at.

racer32
October 5th, 2017, 22:23
Thanks for the quick reply and assessment. It is a bit light. I did my best to get the pattern to show up. I always put drag on the carrier but maybe that is wrong. I'll try it on the pinion. I'll make another adjustment and run it again tomorrow.

md21722
October 5th, 2017, 23:16
I don't see any pictures....

racer32
October 5th, 2017, 23:51
How about these?
https://i.imgur.com/3GLcH5bh.jpg
https://i.imgur.com/2k0iDfMh.jpg

burntkat
October 6th, 2017, 08:25
I'm still learning, but those look pretty good from what I see.

md21722
October 6th, 2017, 11:42
It probably won't make any noise but its too deep. Remove pinion depth shims.

trippled
October 6th, 2017, 11:56
It probably won't make any noise but its too deep. Remove pinion depth shims.

I thought the same.

clydefrog
October 6th, 2017, 21:46
It probably won't make any noise but its too deep. Remove pinion depth shims.
Yep.

It will prob work but is still slightly deep (pinion). If its still apart, wouldn't hurt removing a few thousands on the shims.