Rear CV driveshaft w/ slip yoke (works instead SYE or H&T)

[Achmed]

This is a an OEM XJ rear driveshaft with a CV joint installed at the slip yoke end by a professional driveline shop and ordered for 4 Wheel Parts which is who I got it from. It is in excellent condition with new Spicer 1310 U Joints. This shaft will work in place of a slip yoke/ hack n tap for vehicles lifted 3"-7" and will allow you to simply install shims to correct pinion angle on go. Save yourself the cost of a hack n tap or SYE like I did and simply install this shaft, shim and go.

$75

[Achmed]

The reason I am selling is due to the fact that I had some driveline vibes and thought that I needed to just go ahead and install a hack n tap. However, upon installing the H&T, I realized the vibes were not related to the shaft. So with that being said, this shaft is a substitute for a SYE or H&T. I wish I could have saved myself the $400 for the H&T and custom driveshaft.

[jakethesnake94]

so if i get a 6.5" lift for my 97 jeep cherokee i wont have to spend $250 on a SYE or a H&T

[Achmed]

I have 7.5" of lift on mine and ran this shaft for over a year with NOT A SINGLE problem.

[jakethesnake94]

is the shaft for sell if so how much

[Achmed]

Yes, $75. It is on the first post. ;)

[jakethesnake94]

could u send me a pic of it

[Achmed]

Sure, here you go. From my phone, sorry. I ran this on 7.5" of lift and I also have shackle relocation brackets so the rear of my XJ flex's VERY well. At full flex, this shaft still has 3" of spline contact. Again, it was done for 4 Wheel Parts by a driveline shop.

http://i186.photobucket.com/albums/x147/Chris_Hyde/Miscellaneous/IMG_0001-1.jpg

http://i186.photobucket.com/albums/x147/Chris_Hyde/Miscellaneous/IMG_0002-1.jpg

http://i186.photobucket.com/albums/x147/Chris_Hyde/Miscellaneous/IMG_0003.jpg

[jakethesnake94]

so with this i do not have to purchase a SYE or a H&T with my lift

[Achmed]

That is correct. I ran it with 7.5" of lift for 1 year with NO SYE and my Cherokee literally drives like a Cadillac. The folks here who have ridden in it will agree.

http://i186.photobucket.com/albums/x147/Chris_Hyde/Miscellaneous/IMG_0019-1.jpg

[Achmed]

If you want it, I will do $90 shipped to a Memphis business or $95 shipped to a Memphis residence.

[jakethesnake94]

I'm new to this so my dad will see if this is our best option I'll let u know.
Thanks Jake

[Achmed]

10-4

[Stallacrew]

I'm not bashing your DS, but I don't see what's different from a front drive shaft...I'm not very drive shaft literate.

Please explain.

[MELKORsXJ]

the one he is selling has the "slip" on the yoke/transfercase; whereas a front driveshaft has the "slip" in the shaft, with fixed yokes...

[Stallacrew]

....but I thought the rear shaft had a slip on the transfer case anyhow..... I don't know, I'll take your word for it.

Sure beats buying a H&T though.

[MELKORsXJ]

....but I thought the rear shaft had a slip on the transfer case anyhow..... I don't know, I'll take your word for it.
.

...correct; that's what i said?

[Cnickgo]

PM sent

[256offroad]

what if you bolt up a shortened front driveshaft to that slip yoke piece? so you have 2 slip points?!?

hm......

[Achmed]

You cannot do that.

[Mutant_Xj]

Would you just sell the yoke? if so how much to 17801?

[Achmed]

Sold

[Achmed]

Would you just sell the yoke? if so how much to 17801?

$95 SHIPPED and you get a free driveshaft. :)

Again, it's sold and pending payment. If it falls through, I will post up.

[Mutant_Xj]

If it falls through I'll take it.

[Achmed]

10-4

[Achmed]

Gone! Shipping out tomorrow.

[jakethesnake94]

Achmed, thanks for the info and your time, but I think my dad wants to go through the transfer case and while doing that go ahead and install the SYE/new d-shaft.

[Mutant_Xj]

Achmed, Thanks for the quick response and refund. I was bummed when I found out some one else got it.