In a proud tradition...

[IXNAYXJ]

Every NWFest pre-event forum has had at least one of these. Since the event itself isn't that far off, I figured I'd start this year's. The question is, what do you have to do to get ready?

I need to:

Get new rear leafs.
Do some final fab work on the exo.
Exhaust manifold.
New front seats.
THOR install.

And I'm sure a bunch else. So...what do you have to do before late June?

-----Matt-----

[Blkxjkrawler]

Here's mine, not much but time is at a premium for me these days.
Finish front and rear bumpers.
mount winch
finish rear storage shelf/drawers,
Mount co2 tank
buy a trailer
rework the bumpstops.

-Ryan

[CanMan]

Ball Joints.
Shocks.
Some other small things.
Thats about it.

[IXNAYXJ]

Oh, yeah, I've got to fix my winch or replace it.

-----Matt-----

[Ba-Riedo]

Install THOR's
Drop belly pan- replace front shaft U joints and tranny fluid
Buy/ Install ACRO steering
Install my new bumper
Install heavy duty trac bar, bracket, brace
Cut front THOR bumper plates to size and install with front bumper
Install backup lights on swing out
Get tube flairs built
Install steering box brace
Get spare axle shafts for front
Rework bumpstops f/r
Build stiffer spring packs for rear
Find some way to organize the rear and mount a couple of fire extinguishers
Rhino line bottom of doors and pull trim
Find a locker or limited slip for my 8.25I might be a little busy.:rolleyes:

-Alex

[Avanteone]

De-winterize my enclosed trailer.

Load Jeep.

Stop @ liquor store.


:D

John

[Ba-Riedo]

De-winterize my enclosed trailer.

Load Jeep.

Stop @ liquor store.


:D

John

No, you must build a new XJ that is as good or better on the trail as your YJ. You may begin now.:wave1:

-Alex

[in2fords]

Well my list is short(yea, right)
Install clucth master cylinder, headers/exhaust system and the new brakelines I just got, go thru and check/tighten the bolts on the things I just replaced, I.E. EVERYTHING from front grill to back bumper, install the new drive shafts and break in new motor/transmission/transfer and both axles. Then all i need to do is ship it across the pacific to my new house in Oregon and get settled in. Install lockers and recheck everything again.
I "SHOULD" make it to this one.

[Avanteone]

No, you must build a new XJ that is as good or better on the trail as your YJ. You may begin now.:wave1:

-Alex


I will be building another XJ, just mild /w 31's or 33's..... but it's definitely NOT in the budget before NWFest. :laugh:

J

[TORX]

Realistically...

- Find a full size spare
- Find a way to secure the cargo area
- Swap in a bigger fuel tank (10gal isn't going to cut it)
- Do a coolant flush and burp the system

Perfect World...
- Build a rear bumper and cut the quarters

Nothing to extensive. I should be able to get everything done in time.

[WaXJ_Skier]

1. do something with control arms (long arms or new short arms)
2. Install THOR guards
3. rocker replacement
4. bed line interior of XJ
5. New shocks
6. SYE
7. figure out how to make XJ get 50MPG

probably more that I don't have time for.

[noutlawjeeper]

1. wire lights in my installed thors
2. install 2low
3. possibly steering
4. make something to organize the rear
5. longer front shocks
6. relocate rear shock mounts flush

dreams
7. bumpers f/r
8. winch
9. cage

I'll just stop now, this could go forever.

[ladywolf]

sit back and watch and wish

[XJourney]

Well what "Pre NWfest to do list" would be complete without me :)

1. 33" Bighorns
2. 5" lift
and some fabbing of odds and ends

[2xtreme]

I don't NEED to do anything (Like John ;) )
However, Here is my list of expected mods prior to NW Fest for the XJ:
1. Build Rear tube fenders and light guards
2. Install all new Heims in Steering
3. Mount and Install H1 Double Beadlocks
4. New bellypan and Engine/Tranny skids
5. Install 2Low kit
6. Finish building and wire folding light mount for Exo Cage

Other:
1. Install CB in tow rig


Michael

[Avanteone]

I did forget one thing on my list. I've gotta convince my wife that making 30# of potato salad again will be a worthwhile contribution! hahahaha

J

[noutlawjeeper]

Get on it!

[XJCasper]

Oh boy. The Jeep has been parked and neglected.
This is what should be done.

Front bumper is in the shop getting powdercoated.

Install bumper
Winch
Exhaust manifold
Add tanks for the Air compressor

Clean the webs out.

[mojojojo]

beleive it or not, i am ready now.

still workin on the tow rig thing, but other than that any thing i do between now and then is a bonus. i'm sure that'll change, but it's a great thought aint it ?

[1sickhick]

I need to instal slider's,Front r&p,cut bottom of rear 1/4 panal,find a good rear bumber.Other than that I'm good.looking forward to meeting some of you.

JACK

[poorboy_616]

For me to make it:

Retrain my 87 XJ from Mallcrawler to trail rider, and get my friggin speedometer fixed.....

Oh yeah, find a source of funding....

[WheelinJR]

1. Find the time and money to show up
2. Buy a new Jeep
3. Build said Jeep
4. Realize I'm not going to be building a trail rig this time and accept the fact that I'll be rolling the easy to moderate trails again.

[JBweld]

Install another leaf in my already sagging "new" rear springs.
figure out the wiring problem with my fuse block.
Herculine interior.
Figure out why my OX works sometimes.
Get new tires if I have the money(probably not going to happen)

That's about it.
-Jeremy

[90exjay]

Install another leaf in my already sagging "new" rear springs.
figure out the wiring problem with my fuse block.
Herculine interior.
Figure out why my OX works sometimes.
Get new tires if I have the money(probably not going to happen)

That's about it.
-Jeremy
Gee i wonder where all your money has been going lately :D

Sean

[JBweld]

Gee i wonder where all your money has been going lately :D

Sean

The same place some of yours is going. ;)

[90exjay]

The same place some of yours is going. ;)

Roger that. :thumbup:

On a side note, got my rear disc's and alloys on the 44 done, and upgraded my master and booster too.

Sean

[supsa]

I think I'm ready but not sure if I fixxed the slipping problem. I'll find out this week. Oh ya find $$$ to buy a rear locker and leafs.

[fubar XJ]

Eh, the XJ is pretty much ready to go. Little things come and go, had to replace my aux fan toggle and temp slider light the other day, but nothing major. I suppose I should re-trim my front bumper corners so that they stop rubbing at full stuff, maybe I'll hit that this weekend.

[Ba-Riedo]

I think I'm ready but not sure if I fixxed the slipping problem. I'll find out this week. Oh ya find $$$ to buy a rear locker and leafs.

Did you figure out why it was slipping? And how was the drive home with it?

-Alex

[Muddy Beast]

Well what the heck, I have a few things on my list, so I'll bring this back to life. It's all small stuff, but a long list. The beauty of my first car that I actually car about/is officially mine, and having it be 19years old from idiot owners who dont know how to put back the bolts after they take them off! (Litterally like 50 bolts missing from body parts and a few engine parts)

Things I'm getting in the next week/installing:
-All new hoses
-New Oxygen sensor
-New wiper blades/fixtures
-Fix the windows from sticking (all but the drivers need to be pulled up)
-Replace the oil filter and change the oil
-Drain and replace the Tranny, Diferential, and Radiator fluids
-New coolent reservor
-New Alternator
-Buy and install a CB radio
-Fix the winshield wiper motor (speed doesnt go up, at all)
-Check all the grounds
-New speakers (Some decent Kicker speakers on the way)
-New Dynomax exhaust and welding to new Catylic converter
-Replace the EGR valve hoses

Possibly do/hope to do by NWfest:
-Get a 3" lift from Rough Country
-RC Diff. guard
-RC steering stablizer
-Set of BFG Mud Terrains
-Black Steelies
-Tow points
-Rock sliders

Just finished today:
-new Catylic converter
-new EGR valve
-new Air Filter
-all new lights
-new rear hatch hitches
-rear windshield wiper unit
-adding a full tool box and another tool box with a tow strap, gloves, ect.

[2xtreme]

Updated.

I don't NEED to do anything (Like John ;) )
However, Here is my list of expected mods prior to NW Fest for the XJ:
1. Build Rear tube fenders and light guards (50% complete, hopeing to have done for NW Fest still)
2. Install all new Heims in Steering (Done)
3. Mount and Install H1 Double Beadlocks (Done)
4. New bellypan and Engine/Tranny skids (Done)
5. Install 2Low kit (won't happen before NW Fest)
6. Finish building and wire folding light mount for Exo Cage (Installed, but not wired yet)

Other:
1. Install CB in tow rig (won't happen before NW Fest)


Michael

[XJourney]

Well what "Pre NWfest to do list" would be complete without me :)

1. 33" Bighorns DONE
2. 5" lift DONE
and some fabbing of odds and ends Just a little wiring left to do

[Blkxjkrawler]

Here's mine, not much but time is at a premium for me these days.
Finish front and rear bumpers. Front is done, rear wont be
mount winch Done
finish rear storage shelf/drawers, Getting close
Mount co2 tank Done
buy a trailer Wont happen before NW fest
rework the bumpstops. Wont happen before NW fest

-Ryan
updated as well

[Ba-Riedo]

Install THOR's (done)
Drop belly pan- replace front shaft U joints and tranny fluid (done)
Buy/ Install ACRO steering (done)
Install my new bumper (done)
Install heavy duty trac bar, bracket, brace (done)
Cut front THOR bumper plates to size and install with front bumper (doubtful)
Install backup lights on swing out
Get tube flairs built (done)
Install steering box brace (done)
Get spare axle shafts for front (doubtful)
Rework bumpstops f/r
Build stiffer spring packs for rear (done)
Find some way to organize the rear and mount a couple of fire extinguishers (done sorta)
Rhino line bottom of doors and pull trim
Find a locker or limited slip for my 8.25 (doubtful)I might be a little busy.:rolleyes:

-Alex

[Avanteone]

De-winterize my enclosed trailer.

Load Jeep.

Stop @ liquor store.


:D

John

I've only got the first of the things on my list done. :)

[JBweld]

Install another leaf in my already sagging "new" rear springs.
figure out the wiring problem with my fuse block.
Herculine interior.
Figure out why my OX works sometimes.
Get new tires if I have the money(probably not going to happen)


Huh...that's funny. I got the wheels/tires, and haven't done the other stuff!

-Jeremy

[in2fords]

I highly suggest buying a undercoating sprayer. I just put down a gallon of dupli color in less then 10 minutes!! came out real nice and even and there was no mess to deal with. got my gun from eBay, less then $30 shipped I beleive.
http://i72.photobucket.com/albums/i189/in2fords/Heep/bedliner002.jpg (http://s72.photobucket.com/albums/i189/in2fords/Heep/?action=view&current=bedliner002.jpg)

not real rough but there is a lot of texture

http://i72.photobucket.com/albums/i189/in2fords/Heep/bedliner005.jpg (http://s72.photobucket.com/albums/i189/in2fords/Heep/?action=view&current=bedliner005.jpg)



Im haveing some set backs myself. Put on the new SS braided clutch line and did a bunch of things. Go to start it and just clicking, smell something and think it is the starter motor giving up. Crawl under there and its not hot? crank the motor crossing the terminals on the back of the motor and smell the burning smell again, look over and FIRE!!!! the ground wasnt doing well at all so all the current was going thru the clutch hose :( $50 cluctch hose down the drain.

Now the grounds are all set and good, still need to have drive shafts made and a couple other small things, like SHIPPING IT ACROSS THE OCEAN. not looking good at this point.

[WaXJ_Skier]

1. do something with control arms (long arms or new short arms) Long arms next week
2. Install THOR guards Currently in the living room halfway prepped for paint
3. rocker replacement Holding out hope but probably not
4. bed line interior of XJ Maybe
5. New shocks Maybe
6. SYE Yeah right
7. figure out how to make XJ get 50MPG

probably more that I don't have time for.

Updates

[XJCasper]

Oh boy. The Jeep has been parked and neglected.
This is what should be done.

Front bumper is in the shop getting powdercoated.

Install bumper
Winch
Exhaust manifold
Add tanks for the Air compressor

Clean the webs out.


Updates?

Bumper is back from the powdercoater.
Install? Won't happen
Winch? Won't happen
Exhaust mani? Done, thanks to John's shop.
OBA tanks? Unlikely, but might work out.

Front Locker? Done, due to John's shop.

Wife's to do list due to 9 month of nesting I will summarize to the last and next item?
Sink and new faucet? Done.
Finish off the Water damage in the new nursery? Sheet rock is replaced. Needs to be finished of before primer.

[TRSCobra]

Track bar and steering stabilizer. On order. :scottm:

[GI-John]

Install rear shocks
Install new exhaust
Mooch a spare rim from Jason
Wire driving lights
troubleshoot stereo
Make more beer for NW fest
rear brakes for 8.8


Loving every minute of it!

John

[ethernet]

My list: (hope I can get it done so I can meet some of you guys!)
- install new t-case drop (on it's way, old set magically fell off on my last outting)
- relocate the o2 sensor (guy at the exhaust shop said he would do it but I can't get it down there due to previous problem)
- get a spare (anyone have a 33x12.5 they need to get rid of?)
- get some Clevis D Shackles (probably pick a couple up this evening)
- earn money for gas to get there, while I am there, and to get back
- battery hold down (minor adjustments to be made, just fabbed a new one)
- reconnect all electrical components (cleaned them, and question about it http://www.naxja.org/forum/showthread.php?t=957086&page=3)
- adjust TPS

[JR aka RJROffRoad]

Nothing really panned out for me...I am sitting this year out again.

[Muddy Beast]

Well what the heck, I have a few things on my list, so I'll bring this back to life. It's all small stuff, but a long list. The beauty of my first car that I actually car about/is officially mine, and having it be 19years old from idiot owners who dont know how to put back the bolts after they take them off! (Litterally like 50 bolts missing from body parts and a few engine parts)

Things I'm getting in the next week/installing:
-All new hoses (Done)
-New Oxygen sensor (Done)
-New wiper blades/fixtures (Done)
-Fix the windows from sticking (Not happening for a few weeks...)
-Replace the oil filter and change the oil (This weekend...)
-Drain and replace the Tranny, Diferential, and Radiator fluids (This weekend...)
-New coolent reservor (Done)
-New Alternator (Done)
-Buy and install a CB radio (On the way...)
-Fix the winshield wiper motor (Done)
-Check all the grounds (Done)
-New speakers (Done)
-New Dynomax exhaust and welding to new Catylic converter (Done)
-Replace the EGR valve hoses (Done)

Possibly do/hope to do by NWfest:
-Get a 3" lift from Rough Country (Ordering tomarrow, hopefully installed before NWFest)
-RC Diff. guard (No money)
-RC steering stablizer (No money)
-Set of BFG Mud Terrains (Ordering after I order the lift, on when the lifts on...)
-Black Steelies (No money)
-Tow points (No money)
-Rock sliders (No money)


I've gotten a lot done between my dad and myself working on her, then me and my friend installing the exhaust today...

I'm siked for NWFest even more now, because my dad is loaning me money so I can get a lift and tires hopefully by then. :laugh3:

[Avanteone]

I've gotten a lot done between my dad and myself working on her, then me and my friend installing the exhaust today...

I'm siked for NWFest even more now, because my dad is loaning me money so I can get a lift and tires hopefully by then. :laugh3:

Anything we can do to talk you out of that 3" Rough Country? :laugh3:

[Muddy Beast]

Anything we can do to talk you out of that 3" Rough Country? :laugh3:

Yeah, give me $300 more to buy an RE. The difference in a RC to an RE is more than a weeks paycheck...

I figure I'll probably go bigger in a year anyways.

[Avanteone]

Yeah, give me $300 more to buy an RE. The difference in a RC to an RE is more than a weeks paycheck...

I figure I'll probably go bigger in a year anyways.

That may be true.... but in a year you can get $$$ for good used R.E. components. The same is NOT true for rough country, etc. This is definitely one of those areas where you get what you pay for.

J

[Matt_West]

1. Install Thor Guards
2. Replace lower radiator hose
3. Power Steering cooler
4. Transmission cooler
5. CB (Doubtful)
6. Radio antenna (Doubtful)
7. Cut rear quarters
8. Move spare to different rim
9. Fix drivers side window
10. Battery clamps
11. Check dog into Camp Happy Paws

[TORX]

Updated.

- Find a full size spare - DONE (Thanks FUBAR)
- Cargo area tie-downs - DONE
- Oil Change and other maintenance - DONE
- Temporary hood spacers - DONE
- Tire ROBAL - DONE
- Fix CB Setup - DONE

- Swap in a bigger fuel tank - Not going to happen
- Build a rear bumper and cut the quarters - Not going to happen

[1sickhick]

I need to instal slider's,Front r&p,cut bottom of rear 1/4 panal,find a good rear bumber.Other than that I'm good.looking forward to meeting some of you.

JACK

1.(Sliders) - DONE
2.(Front R&P) - DONE
3.(Bottom of 1/4's) - This weekend
4.(Rear bumper) - not happining

[TORX]

I'm siked for NWFest even more now, because my dad is loaning me money so I can get a lift and tires hopefully by then. :laugh3:
Not to get the thread off topic, but I would advise you to hold off on the purchase until after NWF. There will be a variety of XJ's there for you to look at, and people to talk to first hand. Ride along on some trails, and see how different setups perform.

You may end up changing your mind.

[Avanteone]

I'm closer to being ready.... I got these fancy new cupholders installed!

http://www.boatersworld.com/product/338470024.htm?bct=t13046503%3Bcicabin-galley%3Bcigalley%3Bcidrink-holders

:laugh3:

J

[mojojojo]

beleive it or not, i am ready now.

still workin on the tow rig thing, but other than that any thing i do between now and then is a bonus. i'm sure that'll change, but it's a great thought aint it ?

so, times run out. i got the jeep all ready, got the flat bed, but.....the tow rig isn't happenin. so i'm either drivin the heep both ways or......?

anyone semi local with a tow rig wanna cut a deal ?

[ethernet]

Updated list... Urg...

My list: (hope I can get it done so I can meet some of you guys!)
- clean and grease all electrical connections (done)
- adjust TPS (need help, mechanically inclined... did try however)
- install new t-case drop (should be here Friday)
- brake and e-brake check (next week)
- relocate the o2 sensor (exhaust shop to do once able to drive)
- hold downs for hi-lift and co2 tank
- install CB? (need fuses)
- lightly sand and repaint rims
- fire extinguisher
- gas can?
- radiator flush

buy
- rock rails (not gunna be done for NW Fest...)
- front and rear diff guard? (recommendations?)
- 4.56 gears (dreaming)
- get a spare (in the works)
- front recovery hooks (ordered)
- hose for co2 tank (order tomorrow)

[WaXJ_Skier]

That may be true.... but in a year you can get $$$ for good used R.E. components. The same is NOT true for rough country, etc. This is definitely one of those areas where you get what you pay for.

J

I agree also OME isn't bad Ive got their stuff on my rig and it holds up to some abuse

[XJourney]

I am all done. Changed all my fluids tonight and buttoned up the last few things a couple of minutes ago. I just need to throw in my camping gear and wait till Friday at noon.

[XJourney]

Yeah, give me $300 more to buy an RE. The difference in a RC to an RE is more than a weeks paycheck...

I figure I'll probably go bigger in a year anyways.

I have a pair of RE 3.5" front springs and a set of dakota rear springs that I will be looking to sell at or shorty after NWfest. This set-up has worked great for me, just ask around. (980 on a 20* RTI)

Put your money toward tow hooks since they are required and a Transfer Case skid plate. (nothing cuts in to your upgrade money then tearing your TC off.)

I will put your name on my springs and I am very negotiable on price ;) Talk to me at NWfeast :D

Plus nothing worse then putting on a lift the weekend before an event, guaranteed it will take quite a bit of tweaking before your jeep would be fully ready to wheel. It is the small stuff that will get you everytime.

[Muddy Beast]

Well, unless I can talk my dad into loaning me more money...I'm going to stick to the RC kit...

I dont care about the ride, and I'm not a crazy "wheeler" yet. I understand the mixed feelings on the product, I've read them all, but enough people are happy with it that I cant see myself complaining to much.

[fubar XJ]

I've actually come up with a couple of items in the last week or so:

Re-do track bar attach bracket. The fix I did three months ago is sloppy again. This time, after I plate and match drill the hole, I'm going to lay a couple of tack beads on the bolts once it's tightened. That should add support right on the end of the leverage, but allow me to grind them off in the event I need to remove it.


"Adjust" steering stops by welding a couple small pieces of stock or nuts onto either the factory stud or the corresponding area where it hits on the axle tube/knuckle. My MTRs ride my LCAs a bit at full lock as is, my SSRs have bigger lugs and will hit worse.

This will all be tackled next week.

[WaXJ_Skier]

Updates


1. do something with control arms Long Arms are in Check
2. Install THOR guards Currently in the living room halfway prepped for paint
3. rocker replacement Holding out hope but probably not
4. bed line interior of XJ Girlfriend ground rear down to bare metal mostly
5. New shocks Purchased will be installed when BPEs arrive
6. SYE Yeah right anybody have one thy want to sell for cheap?
7. figure out how to make XJ get 50MPG

probably more that I don't have time for.

[CanMan]

Damn Joe, wish my girlfriend would get out there and work on my junk. She works on my 'other junk' though. ;)

-Finish half cage
-Get 2 new tires, and groove them
-Fill up tank
-Gather up spares
-Install rear seat
-Install rock lights
-Some more small stuff

[Slacker87XJ]

Short list for me:

1. Tires (will be done this Friday).
2. Install CB.
3. Buy 12 cases of oil for the trip. :twak:


-i

[ethernet]

Updated list... Urg...

My list: (hope I can get it done so I can meet some of you guys!)
- clean and grease all electrical connections (done!!)
- adjust TPS (someone coming Tuesday to help me)
- install new t-case drop (planned to be installed tomorrow)
- brake and e-brake check (wednesday)
- spare mounted (wednesday)
- relocate the o2 sensor (exhaust shop to do once able to drive, thursday?)
- hold downs for hi-lift and co2 tank
- install CB and antenna
(http://www.westcoastmall.net/hga1000-high-gear-baseload-magnet-mount-cb-antenna-p-75.html) - lightly sand and repaint rims
- fire extinguisher
- gas can
- radiator flush (tomorrow)
- check grounds (tomorrow)
- oil change (tomorrow)
- check spark plugs (tomorrow)

buy
- rock rails (not gunna be done for NW Fest... :'( )
- front and rear diff guard? (ordered (http://www.tellico4x4.com/product_info.php/cPath/3017_84_2519/products_id/26416))
- 4.56 gears (dreaming)
- front recovery hooks (ordered (http://www.northerntool.com/webapp/wcs/stores/servlet/product_6970_20027_20027?cm_mmc=Housefile-_-SHIPPED-_-1206-_-CONF))
- regulator (hmmm... brithday is Tuesday...)
- bolts for bushwackers

[Ba-Riedo]

Updated list... Urg...

My list: (hope I can get it done so I can meet some of you guys!)
- clean and grease all electrical connections (done!!)
- adjust TPS (someone coming Tuesday to help me)
- install new t-case drop (planned to be installed tomorrow)
- brake and e-brake check (wednesday)
- spare mounted (wednesday)
- relocate the o2 sensor (exhaust shop to do once able to drive, thursday?)
- hold downs for hi-lift and co2 tank
- install CB and antenna
(http://www.westcoastmall.net/hga1000-high-gear-baseload-magnet-mount-cb-antenna-p-75.html)- lightly sand and repaint rims
- fire extinguisher
- gas can
- radiator flush (tomorrow)
- check grounds (tomorrow)
- oil change (tomorrow)
- check spark plugs (tomorrow)

buy
- rock rails (not gunna be done for NW Fest... :'( )
- front and rear diff guard? (ordered (http://www.tellico4x4.com/product_info.php/cPath/3017_84_2519/products_id/26416))
- 4.56 gears (dreaming)
- front recovery hooks (ordered (http://www.northerntool.com/webapp/wcs/stores/servlet/product_6970_20027_20027?cm_mmc=Housefile-_-SHIPPED-_-1206-_-CONF))
- regulator (hmmm... brithday is Tuesday...)
- bolts for bushwackers

I have some stock bushshitter bolts...

-Alex

[ethernet]

Nah I don't want the stock ones. Since they are self tapping. I am going to get some actual bolts and nuts so that I can take my front bushwackers off when I go wheeling.

[Ba-Riedo]

Nah I don't want the stock ones. Since they are self tapping. I am going to get some actual bolts and nuts so that I can take my front bushwackers off when I go wheeling.

I used to use the stock bolts with nuts on the back side, worked great.

-Alex

[ethernet]

I used to use the stock bolts with nuts on the back side, worked great.

-Alex

I couldn't, well, not me, the people at Fasteners couldn't find a nut to fit the self tapping screws.... Maybe I will try that again...

[Ba-Riedo]

I couldn't, well, not me, the people at Fasteners couldn't find a nut to fit the self tapping screws.... Maybe I will try that again...

Mclendons hardware in Woodinville is where I got mine.

-Alex

[ethernet]

Haven't heard of them and that's quite a drive for me but thanks for letting me know there are some to fit it!!

[IXNAYXJ]

I am going to get some actual bolts and nuts so that I can take my front bushwackers off when I go wheeling.Honestly, I wouldn't worry to much about your front ones; I hit my rear flares 50:1 to my front ones.

-----Matt-----

[ethernet]

Is there a way to remove the rear ones and still be able to attach them afterwards? I tried thinking of a way but couldn't come up with one.

[IXNAYXJ]

...be able to attach them afterwards?Why would you want to do that? ;)

-----Matt-----

[ethernet]

Why would you want to do that? ;)
haha... the legallity issues for when i drive on the road around town... i know... it sucks... :D can't say i haven't done if before however...

any ideas on how to do it though?

[2xtreme]

haha... the legallity issues for when i drive on the road around town... i know... it sucks... :D can't say i haven't done if before however...

any ideas on how to do it though?

If you welded the nuts to the back side of the fender you could just un due them from the outside.
If you don't have the ability to weld, you could "cold weld them" that would probably work if you preped the area good enough.
If you were to do this, I would recommend putting additional support under the nuts (either large washers or better yet a strip of steel with the nuts attached on the back.

Michael

[2xtreme]

My last update (I won't be working on the Jeep anymore before NW Fest).

Here is my list of expected mods prior to NW Fest for the XJ:
1. Build Rear tube fenders and light guards (Done)
2. Install all new Heims in Steering (Done)
3. Mount and Install H1 Double Beadlocks (Done)
4. New bellypan and Engine/Tranny skids (Done)
5. Install 2Low kit (won't be done for NW Fest)
6. Finish building and wire folding light mount for Exo Cage (Installed but not wired yet)

Other:
1. Install CB in tow rig (decided not to do this yet, won't really need it for NW Fest anyway)


Michael

[CanMan]

Is there a way to remove the rear ones and still be able to attach them afterwards? I tried thinking of a way but couldn't come up with one.

Quater turn fastners(like what racecars use on body panels), or riv nuts, and remove them before hitting the trail.

[CanMan]

Damn Joe, wish my girlfriend would get out there and work on my junk. She works on my 'other junk' though. ;)

-Finish half cage
-Get 2 new tires, and groove them
-Fill up tank
-Gather up spares
-Install rear seat
-Install rock lights
-Some more small stuff

Half cage.

http://i112.photobucket.com/albums/n187/12GaugeXJ/100_5161.jpg

New tires. Grooved. Damn, small pics. Camera phone took em.

http://i112.photobucket.com/albums/n187/12GaugeXJ/79014fbbacf6.jpg

http://i112.photobucket.com/albums/n187/12GaugeXJ/477cb3d6fd8d.jpg

Gas tank full.

Spares gathered.

Rear seat in.

http://i112.photobucket.com/albums/n187/12GaugeXJ/100_5157.jpg

Rock lights in/replaced (old ones burnt out).

http://i112.photobucket.com/albums/n187/12GaugeXJ/100_5164.jpg

Also added a PS cooler.

http://i112.photobucket.com/albums/n187/12GaugeXJ/100_5167.jpg

Got to make rear seatbelt tabs off the cage, install 2 more speakers, adjust half door hinges, cover hole above muffler on floorboard, adjust E brake, and a few other small things Im sure Im forgetting.

[JBweld]

That's looking pretty good Eli! Can you post up a bigger picture of your grooved tire? I want to see how you did yours. Are they regular TSL's?

I'm really envious of you guys. I wish I could go :mad:

-Jeremy

[Avanteone]

That's looking pretty good Eli! Can you post up a bigger picture of your grooved tire? I want to see how you did yours. Are they regular TSL's?

I'm really envious of you guys. I wish I could go :mad:

-Jeremy

I still say you should just show up, we'll find you a seat!

[fubar XJ]

You can ride with me, Jeremy. Sounds like you've got more issues going than just the XJ not being ready though, so it's all good.

PM me if you want to ride over and hit the trails with me. I'm leaving early Friday morning.

[CanMan]

That's looking pretty good Eli! Can you post up a bigger picture of your grooved tire? I want to see how you did yours. Are they regular TSL's?

I'm really envious of you guys. I wish I could go :mad:

-Jeremy

Thanks, Its getting there.

Here's a thread I did on the tires a while ago, they are the same way now. Seems to work well, plus it gives you 3 center lugs, instead of 2(If you cut them in the middle). http://www.naxja.org/forum/showthread.php?t=929503

They are regular bias ply TSL's. If they make an SX in a 33x12.50x15, Id run them instead. These are plenty strong anyways.

Like everyone's said, catch a ride homie.

[JBweld]

Here's a thread I did on the tires a while ago, they are the same way now. Seems to work well, plus it gives you 3 center lugs, instead of 2(If you cut them in the middle). http://www.naxja.org/forum/showthread.php?t=929503


Cool. That's how I did mine too.

[in2fords]

I wish I could make it but its not in the cards this year. I will be on the west coast early next month but wont be ready for a trail for atleast a month.

(the other)Jeremy

[Matt_West]

1. Install Thor Guards (DONE)
2. Replace lower radiator hose (DONE)
3. Power Steering cooler (Not happening)
4. Transmission cooler (Not happening)
5. CB (Doubtful) (DONE)
6. Radio antenna (Doubtful) (Not happening)
7. Cut rear quarters (Not happening)
8. Move spare to different rim (DONE)
9. Fix drivers side window (DONE)
10. Battery clamps (Wood screw) :doh:
11. Check dog into Camp Happy Paws Tomorrow

Added: Christy helped me out so some things not on the list were done. Tie downs, painted trim, painted bumper, cleaned Jeep

[CanMan]

Got to make rear seatbelt tabs off the cage,
install 2 more speakers,
adjust half door hinges,
cover hole above muffler on floorboard,
adjust E brake,
and a few other small things Im sure Im forgetting.

Done, in and bolted.

Done, quick removal from rear hatch.

Will do that tomorrow at work.

Done with license plate.

Done, but need to adjust shoes inside rotor.

:dunno: on the few small things.

[WaXJ_Skier]

my THORs are painted

[Ba-Riedo]

my THORs are painted

About time.

-Alex

[ethernet]

Update:

My list: (hope I can get it done so I can meet some of you guys!)
- clean and grease all electrical connections (done!!)
- adjust TPS (done! will recheck)
- install new t-case drop (ran into problems, will finish tomorrow, I guess it is today now...)
- brake and e-brake check (today)
- spare mounted (today)
- relocate the o2 sensor (today)
(http://www.westcoastmall.net/hga1000-high-gear-baseload-magnet-mount-cb-antenna-p-75.html) - lightly sand and repaint rims (today)
- radiator flush (today)
- install CB and antenna (http://www.westcoastmall.net/hga1000-high-gear-baseload-magnet-mount-cb-antenna-p-75.html) (today)
- check grounds (done)
- oil change (done)
- check spark plugs (done)
- install differential guards (friday)
- mount front tow hooks (friday)
- nutserts for bushwackers (today)

Let's see if it all gets done......

[ethernet]

All that work to go wheel with you guys and one phone call changes everything...

Dispatched called. I am headed out on the fireline!!!

[WaXJ_Skier]

All that work to go wheel with you guys and one phone call changes everything...

Dispatched called. I am headed out on the fireline!!!
that sucks, stay safe so you can wheel another time.

[ethernet]

Doesn't suck actually. Making $15 and hour and working 90 hours a week is really nice. Especially the 50 hours of OT!! More money for wheeling! :D Safety is number one!