PDA

View Full Version : Parting 94 Country


OverlandXJ
July 23rd, 2007, 13:22
I'll be parting my wife's 94 here soon. It has rotted floors, so i picked her up a ZJ i'm almost done with.

Black Country with grey fabric interior. The fenders have both been hit while it sat in parking lots, the pass side rear door also has a dent. Headliner is falling, no sound bar or overhead console on this.

4.0L runs well with a touch of smoke at cold start, oil filter adaptor needs oring kit. This Jeep has never failed to start, but it's always had a louder lifter tap than my 94 Sport. I bought it with 40k and it's now a little over 100k. Has good oil pressure.

AW4 (23 spline)..never any issues. I'll be keeping the fresh 242 in it for a replacement to the ZJ's 249. The Country wheels have been swapped to the ZJ, it now has 5 spokes that have seen better days...but like new tires.

Dana 30 and C8.25 with 3:55 gearing.

I'll be taking the front rotors and GDI rad out for my rig. Everything else is available. Cannot ship heavier/larger items. Engine,trans and axles will need to be picked up. Also having an issue with my digital camera...keeps powering off, i will give accurate honest descriptions if i cant seem to take a pic.

Jeep will be parted in about 2-3 weeks. If you want it all, $800 and bring a trailer.

lobsterdmb
July 23rd, 2007, 17:27
how much for the dana 30 shafts and the C8.25 shafts?

OverlandXJ
July 24th, 2007, 05:56
how much for the dana 30 shafts and the C8.25 shafts?

Hows $125 for the complete rear 8.25 and D30 shafts sound?

jp4wheelin16
July 25th, 2007, 20:44
how much for the whole motor and the computer to go along with it?

lobsterdmb
July 26th, 2007, 06:30
Hows $125 for the complete rear 8.25 and D30 shafts sound?

i'll take them all if the dana30 shafts are 297's.

OverlandXJ
July 26th, 2007, 07:25
i'll take them all if the dana30 shafts are 297's.

The 30 shafts are 260 joints John, and the rear would be 27 spline.

OverlandXJ
July 26th, 2007, 07:30
how much for the whole motor and the computer to go along with it?

Complete engine with accesories and computer $450. That includes the oilpan to intake manifold and all acc including sensors.

dman
July 30th, 2007, 07:02
Did you sell the D30 or C8.25?

Is the D30 a disconnect?

Thanks!!

Dan

OverlandXJ
July 30th, 2007, 08:30
Did you sell the D30 or C8.25?

Is the D30 a disconnect?

Thanks!!

Dan


Still available. Axle is non disconnect.

JeepinCoastie
July 30th, 2007, 10:20
stil have the engine ... just need engine no cumputer or anything

OverlandXJ
July 30th, 2007, 11:27
Yes, Jeep is still intact. Havent started stripping it yet, wife is still driving it. PM me an offer on what you need.

lobsterdmb
July 31st, 2007, 14:49
The 30 shafts are 260 joints John, and the rear would be 27 spline.


i'll pass

dman
August 8th, 2007, 06:35
Whats the status on the 8.25?

OverlandXJ
August 8th, 2007, 06:44
Whats the status on the 8.25?

I forgot to reply to your PM didnt i?...my apologies. It's available but the Jeep is still being driven...it will be parted soon. I'll consider you having "dibs" if you like.

nhrocker
August 11th, 2007, 09:24
How soon is this getting parted?

On a rush search for the plastic wire harness "rail" that sits between the valve cover and fuel rail as well as the wiring harness that runs through it, from where it separates from the main bundle on the firewall all the way to the plugs (O2, front engine temp sensor, injectors, throttlebody, etc.) and I also need the plug for the rear engine temp sensor.

dman
August 13th, 2007, 05:33
Thanks John, but I have since found one locally.

Thanks for your time!!!

Dan

Ricky
August 13th, 2007, 11:12
How much for the whole front axle?

bronco2man
August 15th, 2007, 08:26
how much for the warning buzzer and fuse box?