Super 30

[hologram]

One of the Creasy offroad workers is putting a dana 60 in his wrangler and is getting rid of his super 30, 4:56 gears, and detroit locker. He will sell and install it for me for $1100. Is this a good deal?
Thanks,
Seth

[0313]

One of the Creasy offroad workers is putting a dana 60 in his wrangler and is getting rid of his super 30, 4:56 gears, and detroit locker. He will sell and install it for me for $1100. Is this a good deal?
Thanks,
Seth

Dunno.

[DrMoab]

One of the Creasy offroad workers is putting a dana 60 in his wrangler and is getting rid of his super 30, 4:56 gears, and detroit locker. He will sell and install it for me for $1100. Is this a good deal?
Thanks,
Seth
Super 30 as in Front? Or SUper 35 as in rear?

[hologram]

as in front.

[Geepfreak]

Seth,, does the axle come with lock-out hub conversion?

[JEEPZZ]

One of the Creasy offroad workers is putting a dana 60 in his wrangler and is getting rid of his super 30, 4:56 gears, and detroit locker. He will sell and install it for me for $1100. Is this a good deal?
Thanks,
Seth
I was under the impression that the Super30 kit only came with an ARB locker.

[Geepfreak]

I was under the impression that the Super30 kit only came with an ARB locker.


My research says the same thing, I guess it is possible they replaced the ARB with a Detroit, But then if they did replace it, I might be leary of, does it really have the 4340 shafts? and the super joints.. Or were those taken out as well.:dunno:

[Big Red]

That's a good chunk of change to spend on a built up dana 30, but it should be pretty stout. I'd try to see if you can get him under $850 or so. A big thing is whether or not it has manual hubs, nice strong u-joints like CTMs or OX and only then would I say yeah, it is close to $1K, but that you could do much better with getting a Waggy dana 44 and building it up. It's up to you, but if I had that $ into a front axle, I'd want to feel good about it going in a dana 44, 60 or something else rather than a polished factory axle.

In summary, I'd only get it if it has manual hubs, strong alloy aftermarket u-joints and other bling things.

Troy

[hologram]

Thanks guy's.
I've decided against it. But I am getting my gears and driveline done in the next week or so. That mean's I can actually do something besides web wheel. :laugh3:

[XJEEPER]

Not that I have any first-hand knowledge regarding Creasey.....but I've had to help fix a YJ that they built up AmFork Cyn last summer, the engineering was poor and actually caused the breakage. I'm leery of anything they turn out, regardless of the $$ deal.

Rocklogic (Von Werritt) or Outer Limits (JR and Doug are out there)

[hologram]

Thanks for the heads up. :wave:

[DrMoab]

Not that I have any first-hand knowledge regarding Creasey.....but I've had to help fix a YJ that they built up AmFork Cyn last summer, the engineering was poor and actually caused the breakage. I'm leery of anything they turn out, regardless of the $$ deal.

Rocklogic (Von Werritt) or Outer Limits (JR and Doug are out there)
Is that the dude in that green Wrangler? If so yeah...I would run away too.

[xj4moab]

Yea can you say spot welds instead of a full bead :eek: not good work

[hologram]

They also told me that I didn't need a new carrier in my dana 30 to go from 3:07's to 4:56's. 4wheel parts, Mepco, Six states, and Gaylon Pugh told me that I do. Hmmmmm!

[Geepfreak]

They also told me that I didn't need a new carrier in my dana 30 to go from 3:07's to 4:56's. hahahahaaaa :scared:
4wheel parts, Mepco, Six states, and Gaylon Pugh told me that I do. Hmmmmm!

Even 4 wheel parts got that one right..