dana44, 9 inch, assorted parts

[Classicfury3]

Ford 9" rear from 78 Bronco with detroit locker and 4.56 gears, 0 miles! no brakes. $450 (locker, gears and install kit was $600 new)
http://i289.photobucket.com/albums/ll219/marinexj/P1010262.jpg
http://i289.photobucket.com/albums/ll219/marinexj/P1010261.jpg
Ford HP dana 44 detroit w/ 4.56 gears, 0 miles, installed in cast housing from 78 bronco $500 (locker gears and install kit was $700 new)
http://i289.photobucket.com/albums/ll219/marinexj/P1010371.jpg

Ford 9" stock from 75 f100, 3.55 gears, open carrier $150
http://i289.photobucket.com/albums/ll219/marinexj/P1010370.jpg
Ford HP dana 44 housing with stock 3.55 gears and carrier, stock shafts, all mounts removed... $100
http://i289.photobucket.com/albums/ll219/marinexj/P1010258.jpg

1.5" lift u-bolt eliminators from Treks offroad (TnT Customs) $100
http://i289.photobucket.com/albums/ll219/marinexj/P1010230.jpg

TMR 1/8" steel front unibody stiffeners.. this pic is from their website, they are still in original packaging $100
http://www.naxja.org/forum/Parts_and_Services_files/IMG_0487.jpg

1" lift boomerang shackles for XJ $80
http://i289.photobucket.com/albums/ll219/marinexj/P1010231.jpg

I also have a complete highsteer setup for the dana 44, i paid $1200 for the whole setup, if interested in parts or everything let me know...
http://i289.photobucket.com/albums/ll219/marinexj/P1010240.jpg

[The Hard Struggler]

How much for the knuckles, hi steer arms, ball joints, spindles, calipers and brackets?

The spindles are GM small bearing I assume? New or used?

Thanks.:wave1:

[Classicfury3]

HarshTerrain High Steering setup. Chevy flattop knuckles, used, media blasted, machined and tapped, Brand new ball joints installed. Chevy small bearing spindles, lightly used in good condition. Chevy disc brake brackets, remanufactured calipers with Brand new brake pads. Harsh Terrain Highsteer arms, 4 one ton tie rod ends. Also, brand new Ford Hub and rotors, 5 on 5.5 pattern. Would like $950 for all. All you need are hubs and wheel bearings and knuckles out are complete!

If you dont want the ford hubs and rotors, its $850...

[The Hard Struggler]

Don't need the tie rod ends. I already have hubs, rotors, bearings.

Are the spindles original 72-77 Chevy, or are they newer replacements, as in not 35 odd years old.

Possibly don't need the ball joints either, Ballistic Fab is soon to come out with a super duper rebuildable set, just don't know when they will be released.

Do the Harsh Terrain arms have any bevel to account for caster, or are they flat? I can't quite tell in the pic.

The calipers and pads I will likely be able to pick up local for the same as shipping.


Thanks.

[TheSandman]

The HP44 from the 78 Bronco with 4.88's. I can't tell nor knowledge, but is that a driver side pinion setup? Who did the gear install?

Where in NC are you?

That's actually exactly what I'm looking for.

[Classicfury3]

i believe the arms have 10 degree bevel, ball joint are alredy installed so they are along for the ride... I honestly have no idea on the spindles, but here is a closer pic
http://i289.photobucket.com/albums/ll219/marinexj/P1010336.jpg



yes, its a driver side drop. Gears were set up by a mechanic friend of mine, you can still pull the cover and see the gear pattern if you want, like i said they have never been run... i am in New Bern, NC 28562

[TheSandman]

yes, its a driver side drop. Gears were set up by a mechanic friend of mine, you can still pull the cover and see the gear pattern if you want, like i said they have never been run... i am in New Bern, NC 28562

PM sent

[Classicfury3]

UPDATE

My memory failed me, I pulled the cover on the 44 and they were built with 4.56 gears, not 4.88 as stated in the original post.

So, both the 9 inch with the detroit and the hp44 with the detroit have 4.56 gears!


If a mod could change my first post with this info that would be great!

[Classicfury3]

PacificEd, you are awesome! thanks for the edit!

stock dana 44 housing has been sold

[redneck]

PM sent on boomerang shackles

[Classicfury3]

Still available! Someone wants this stuff!

[440swepty]

What diameter housing do the tnt perches fit? thanks, kevin

[Classicfury3]

they are the large set to fit a ford 9 inch... 3.25"

[440swepty]

PM sent. Kevin

[TheSandman]

another pm sent

[Classicfury3]

U bolt eleminators, shackles, and stock 9 inch sold...

Someone wants full widths with detroits and 4.56's! They are brand new, you cant buy them for what I am asking..... bumpity bump...

[obx-xj]

I might be interested in the pair would you be willing to ship? And where in NC are you?

[Classicfury3]

Axles are sold!
All that is left is the dana 44 highsteer setup, and the TMR front frame stiffeners.
Open to offers before they go on ebay...

[Classicfury3]

Ill take $800 for the whole dana 44 highsteer setup, and $100 shipped for the TMR front frame stiffeners... or best offer...

[Classicfury3]

Frame stiffeners sold! $700 obo on the highsteer, I don't need it, it needs to be put under someone's rig!