The Box (The whole box)

[The Box]

1999 Limited XJ 4.0L
(A/C, keyless entry, power everything, leather interior, XM radio, cruise control)
142K miles

Axles:
Front axle:
D30
ARB
30 spline shafts,
alloy joints
4.56 gears
.25"control arm mounts
alloy seals
teraflex: high steer knuckle, tie rod, drag link
Solid cover

Rear axle:
D44
ARB
4.56
teraflex disk brakes
Solid cover
Ubolt eliminator kit
flush mount shock tabs

Steering:
PSC Extreme Duty Gear and pump, remote reservoir, cooler

Tcase:
TeraLo 4.1 transfer case w/ SYE

Armor/Recovery:
Roxolid Fabrications front bumper
AJ's offroad super rails
DPG gas tank skid
Rubicon Express Extreme Duty belly pan
SuperWinch X9 with 3/8cable and remote

Suspension:
REAR- Old Man Emu HD leaf springs
2" Teraflex boomerang shackles
shackle relocation bracket
RE 18" steel braided brake line
Old Man Emu shocks

FRONT- Rubicon Express 5.5" coils
Rubicon Express Extreme Duty Long Arm Kit
JKS steel braided brake lines
JKS Quicker disconnects
Old Man Emu long travel shocks

Wheels/Tires:
15/8" Black Rock Crawlers
35/12.50/15r Mickey Thompson MTZ's (about 500 miles on them)

Misc:
M.O.R.E motor mounts
Daystar Transmission mount
Onboard air, ARB highoutput compressor
Gibson catback exhaust
Power steering cooler
Intake tube and cone filter
Spare leather front seats out of a '00 (both power, heated, wiring/ switches included)
Spare woodgrain dash panel and overhead console
Lebaron hood vents
rear drive shaft custom Atlanta Driveline
front drive shaft custom Sonnys Driveline(knoxville)
Heavy Duty tow hitch (not sure of class)
spare rear leaf spring bushings (Energy Suspensions) (couldn't buy the one bushing I needed so I had to buy the whole kit.)

Records:
I have most if not all receipts of parts bought and installed professionally. Including service records and repairs (fuel pump) done by Jeep dealerships.

This jeep runs beautifully. The engine runs like new and everything works great. if you would like to see anything specific just ask and I can take pics.

I do not abuse this jeep, below is a clip of the jeep in use.

http://www.youtube.com/watch?v=v5nOAVhf8ws


email at danpascalept@hotmail.com

Asking: $11,000

http://i263.photobucket.com/albums/ii154/danpascale/P1000561.jpg
http://i263.photobucket.com/albums/ii154/danpascale/P1000565.jpg
http://i263.photobucket.com/albums/ii154/danpascale/P1000564.jpg
http://i263.photobucket.com/albums/ii154/danpascale/P1000257-1.jpg
http://i263.photobucket.com/albums/ii154/danpascale/P1000258-1.jpg
http://i263.photobucket.com/albums/ii154/danpascale/P1000582.jpg
http://i263.photobucket.com/albums/ii154/danpascale/cherok7.jpg
http://i263.photobucket.com/albums/ii154/danpascale/cherok8.jpg

[shortxjdoug]

i wish i could have the whole box..... to bad im poor and have vehicles of no value ;)

[The Box]

lol, that ranger you are building is gonna be sick... it blows my mine how expensive parts are when they are just parts, but when you install them it seems like suddenly they lose all their value.

[shortxjdoug]

lol, that ranger you are building is gonna be sick... it blows my mine how expensive parts are when they are just parts, but when you install them it seems like suddenly they lose all their value.

yup thats the curse if i tallied up whats in the wag its way more than what its ever gonna be worth

[dave92cherokee]

A little off topic but are those the factory xj leather seats or did they come from something else?

[The Box]

Yes, they are factory.

[The Box]

$10,000

[The Box]

If you can get close then make an offer.

[Team Willys]

Dude, c'mon... why are you selling the jeep? You know its a decision you will regret...

[The Box]

I got a plan.... I think.
Plus I want something that doesn't have so much money in it so I can get more rough with it and not feel bad when something F's up, preferably open top.

[LiL Timmy]

Ill buy your rear axle if u want to part with it?

[The Box]

Sorry not parting it out.

[shortxjdoug]

really if i could afford this dan id be first in line.... you tried listing it a little more nationally? maybe pirate? it might take the right buyer from farther away

[The Box]

I have it on craigslist, but pirate and prob a couple others would be a good idea too. Thanks man.

[YJ-GENRAL]

i got my truck on autotrader. and so far i have had several offers.

[LiL Timmy]

Well if you consider it let me know, i have the 29 spline 8.25 under mine that I could give you to put under yours. Pm me if you change your mind I have cash!

[MELKORsXJ]

such a nice jeep...

you better not end up with a yota or something!

(jarrad - you need to call that guy who wanted to buy your XJ, i'm sure he'd be interested in Dan's XJ)

[The Box]

Blake- Thanks bud, I checked it out but don't want to drop $25 for just a couple week ad right now. I don't know how well the autotrader demographic would accept my cherokee either.

Lil Timmy- Thanks, I will keep that in mind.

Dan- no yotas for me, I wouldn't mind a cj7 or something like that though. And yea if you know anybody that might have interest, let them know I would def appreciate it.

[LiL Timmy]

That's true dan aka melkor but I don't have his number:( ill tell everyone I know about it dan! Aka the box

[The Box]

hahaha, thanks man!

[DrRandy]

lol, that ranger you are building is gonna be sick... it blows my mine how expensive parts are when they are just parts, but when you install them it seems like suddenly they lose all their value.

X1,000!!

[The Box]

ttt

[YJ-GENRAL]

did you ever sell this beast?

[The Box]

No, I have a trade in the works. I'll update you next week if it works out. I don't wanna jinx it quite yet.

[Team Willys]

It best be a 4 letter word and have a 7 slot grille... or 9 if it's a military version and has flip around headlights!

[The Box]

Well, the trade went through and even thought I said I wouldn't drive anything but a Jeep I ended up with my first Toyota.

Its a 1973 FJ40 with TPI 5.7, D60 front 35spl arb, 9" rear detroit, th350 auto, STAK 3speed tcase, full cage, warn 8274 and 38's

Carl (flameredtj) and I took a road trip out to Nevada to do the swap, got to see a lot of the country. We're actually driving back through Utah right now. Earlier we took the Dodge 2500 out on the salt flats and did some doughnuts and made some passes.

We left weds at 6am and drove nonstop to Battle Mountain NV in 37ish hours. Probably not the smartest deal logistically but I like the rig and always wanted to take a trip cross-country. Really makes you realize how big the country really is.

Anyways, I'll make a pic thread when I get back home.

[shortxjdoug]

hawt! cant wait to see it dan! now you can really play on some big rocks... so when we goin wheelin...


..... and i dont care what anyone says, im not brand loyal at all, if its got four wheels and i can figure out a way to make it go i'll rock it ;)



edit: youve got a phone, walk outside and take a picture to post for us!

[The Box]

Thanks Doug, funny thing is I'm a Jeep only dude but this thing is about as close as it gets to a Jeep without being one. Plus there aren't really any Toyota parts on it besides the frame and body.

We're still driving right now so I'm actually posting from my phone. I'm not sure I can do pics from it since I would need photobucket. I'll give it a shot though.

[High2by]

Sounds nice. Can't wait to see it.

[The Box]

Thanks Mark.

Here's a cell phone pic from this morning.

http://i263.photobucket.com/albums/ii154/danpascale/utf-8BSU1HMDA0MDEuanBn.jpg

[FlameRedTJ]

I feel dirty just towing it. Unfortunantly it hasn't fallen off yet. Even the truckers keep calling it a jeep.

[shortxjdoug]

Thanks Mark.

Here's a cell phone pic from this morning.

http://i263.photobucket.com/albums/ii154/danpascale/utf-8BSU1HMDA0MDEuanBn.jpg

i think i just wet my pants a little bit.... thats a gorgeous rig Dan, sounds like its got all the right parts on the inside. you planning on wheeling it like its built to be wheeled?

[High2by]

Oh man!!! That looks ....can't find the words. Holy Crap!!!

[YJ-GENRAL]

THAT IS A SEXY BITCH!

found the words for you mark...

that is seriously awesome dude... the FJ40 is ONE of my altime favorites if done right, and that my friend is done right... what i dont get though is the fact that you drove out to nevada to pick this thing up and didnt swing by moab to test it out!!!!

andd i thought you were getting rid of the jeep because of money and no time to wheel... that thing better get wheeled now!

[shortxjdoug]

... that thing better get wheeled now!

it will.... even if we have to tie him to the driver seat and force him too ;)

[FlameRedTJ]

THAT IS A SEXY BITCH!

found the words for you mark...

that is seriously awesome dude... the FJ40 is ONE of my altime favorites if done right, and that my friend is done right... what i dont get though is the fact that you drove out to nevada to pick this thing up and didnt swing by moab to test it out!!!!

andd i thought you were getting rid of the jeep because of money and no time to wheel... that thing better get wheeled now!

it's rear engine right now. We were like 20 mins from
Moab and could have taken the box. Wish I could have brought mine :(

[shortxjdoug]

it's rear engine right now. We were like 20 mins from
Moab and could have taken the box. Wish I could have brought mine :(


i wondered what that funny looking thing in the back was, so you have to finish it?

[The Box]

Hahaha thanks guys.

when I originally went to sell it I was going to use part of the money for an engagement and with the rest I was gonna pick up an old cj and beat it. Well I figured out the ring situation and always missed the open top from my old YJ. Plus I was jealous of all the fun you guys were having with the skinny pedal. I plan in keeping with my light foot style in the rocks but now I can stick my foot in it and not worry about it. Only catch with it is that he had an LS1 in it before and wanted $3K on the deal for it. He pulled that and traded straight up for the TPI, its got a spun rod bearing which needs to be fixed along with a couple loose ends. Got all the parts just needs the time. The motor is actually in the bed which is probably why its squating in the rear and sittin tall in the front. I can't wait to get it running though.

[shortxjdoug]

Hahaha thanks guys.

when I originally went to sell it I was going to use part of the money for an engagement and with the rest I was gonna pick up an old cj and beat it. Well I figured out the ring situation and always missed the open top from my old YJ. Plus I was jealous of all the fun you guys were having with the skinny pedal. I plan in keeping with my light foot style in the rocks but now I can stick my foot in it and not worry about it. Only catch with it is that he had an LS1 in it before and wanted $3K on the deal for it. He pulled that and traded straight up for the TPI, its got a spun rod bearing which needs to be fixed along with a couple loose ends. Got all the parts just needs the time. The motor is actually in the bed which is probably why its squating in the rear and sittin tall in the front. I can't wait to get it running though.


sweet, that sucker would be NASTY with an ls1, the tpi should be enough for you... if not theres a guy in knoxville with complete LM7 motors (gen3 5.3's) with all the goodies on the shelf for around 700

[The Box]

Go to youtube and search "aggro sluice" and you can see it with the LS1 and different body tub.

The guy was finishg up a rebuild on it when he went to sell it which is why it still has some odds and ends to finish. It sounded real good with that vette motor, woulda been nice if he would left it in there.

[shortxjdoug]

ive actually seen this one before... nice ride
http://www.youtube.com/watch?v=boEUr3d0jWY

by the way if you want a hand finishing it dont hesitate to call, it looks like a fun project

[Team Willys]

Nice, he was friggen haulin'!

[MELKORsXJ]

...and you ended up with a yota anyways!

Its all good though, the fj40 is an awesome rig... I would wheel one :)

...the video was pretty cool too! Now if we could only get Dan to drive like that! :)

[The Box]

Doug, I'm probably gonna have to take you up on that bud.

Dan, I don't think I'll be as apprehensive about using the skinny on this one. Its a little more heavy duty then The Box was. Probably won't jump it or anything, but def won't be afraid of a good bump every once in a while. :)

[bmanga]

That is the shiznit dude! :yelclap:

[Team Willys]

Haha, why a 5.3 truck engine??? My vote goes to this:

http://i508.photobucket.com/albums/s321/72mustang-man/LSX454.jpg

454 cubic inch LSX block. 620 HP and 590 Lb/Ft TQ. Of course you would have to ditch the carb in favor of fuel injection, but thats no big deal!

[bmanga]

or this:

http://static.summitracing.com/global/images/prod/large/nal-12499121_w.jpg

[FlameRedTJ]

Why even deal with spark plugs and distributors when you can have something that will last forever.

http://img.alibaba.com/photo/11641531/Cummins_6bt_Diesel_Engine.jpg
:scared:

and make some insane power.

[Team Willys]

OOOOOO 6BT CUMMINS FTW!

Eh, the LSX I posted is the lightest of them all (of the posted engines anyway) and makes the most power in pictured form. Yes the cummins can make more with a pretty substantial amount of work, but it still weighs an awful lot...

[FlameRedTJ]

Well yea its over 1k lbs. I'd like to do a 4BT in my TJ but its still about 700ish, and just not sure I wanna listen to the rattle on the trail. Its either that or 5.7 Hemi.

Not sure what the 12V is rated at but my common rail 24V specs 610 ftlbs.

[Team Willys]

A 12V like pictured is only about 500 lb/ft... in stock form.