The "Hope I get it done by WF Oh-Ten" thread

[XJ&CHZ4ME]

As with every big trip, there are always projects getting tied up or new things added to peoples rigs, so what kind of projects (realistic or not :D) do you all have going on? I mean, come on, we have like 7 months to get things done and Christmas for all of those extra goodies etc...

I am going to complete my tail light boxes and pretty much leave evreything else alone (yeah right) unless something breaks between now and then....:D

(insert Mr. T voice here) Post up fools!

[REWSTER]

i got a T-case skid that i need to put on, also want to find a gas tank skid so i dont pop my plastic tank on a rock or something, want to get some lights for my roof rack but that wont matter

im sure other things will pop up within 7 months

[XJ Stryker]

Depends on what I get for My B-day and Christmas but I would be happy just drivin it like it is now.

Maybe If I am lucky I will be done saving up for gears and a front Locker.

[FlexdXJ]

Shooting for 31's and a winch before WF!



Oh and a skid plate that doesn't hang down as far! :D

[BOB]

turn the ignition key...pull her out of the garage....DONE!

:greensmok

BOB

[BRIANHO13]

turn the ignition key...pull her out of the garage....DONE!

:greensmok

BOB


That would be nice, but I will probably try something like linked and rear steered for wf.......

[Sponge Bob]

Get all 3 jeeps in running order so i can pick one depending on the weather conditions. i don't think i have enough money or time for that so i guess what ever is running will be there.

[HaleYes]

My only plans are to adopt a noob.

[Sponge Bob]

My only plans are to adopt a noob.

Can ya just rent one for the weekend? :dunce:

[poorboy87]

Well if funds are in order i may make this one. Ill have to...
Swap out the worn out VD30 for a newer D30. (Vac 30 needs ujoints and balljoints)
Front and Rear tow points.
Fire Extinquisher
Maybe budget boost.

[IllianaXJ]

Fix the same steering box I needed to fix before last year.

Fill up with gas.

[Rev Den]

Refuse

Trace electrical problem if it remains after refuse

Put gas in it.

Load on trailer


Rev

[poorboy87]

And fix my steering box. Its Schloppy.

[XJ&CHZ4ME]

I may throw hydro assist on my list if I get ambitious enough. I have had the parts for a while now...or like some of the others, I might just put gas in it and load it on the trailer :dunno:

[FlexdXJ]

Well, the slight elevation change will be taking affect sooner than i thought. Picking up a set of 31x10.5 Baja Claws from Big Hank's brother next friday as long as they are in reasonable shape. The price is definitely right! So, that means I can get my backbone ordered soon followed by a winch for christmas! :D

[hanaxj87]

Want a big front axle with selectable locker.
New steering linkage.
Roll cage.
Reinforce rear bumper mounts.
Finish on board welder.
Install on board air.
Re do the spare tire carrier.
Install lower control arm drop brackets.
Replace cracked windshield.
Replace all worn bushings.
Drill the other 16 holes for 32 bolt beadlocks.

I'll be lucky if I get half this done.:D

Nick

[XJ&CHZ4ME]

I am thinking about adding cage to my list, but time and $ will be the deciding factor on that I am sure.

[FlexdXJ]

Cage is far far far dowmn the list of mods for me! Its looking like it'll be on 31's with either a winch bumper or backbone with an XRC 8 resting on it! :D

[Stuntman Mot]

build sliders, belly armor and a gas tank skid

[HaleYes]

OK, I've made a list. Not sure that I'll wheel but, I need to get this stuff done.



Fix my church-going floor.
Install JCR Offroad Rear Quarter Guards (http://www.naxja.org/forum/showpost.php?p=244537682&postcount=9).:D
Install JCR Offroad 1 Ton Steering (http://www.jcroffroad.com/Merchant2/merchant.mvc?Screen=PROD&Product_Code=1TNSTOTK&Category_Code=S6).:D
Complete in-cab winch controls.
Install new thimble/hook on winch line.
Eat pig Sept. 5th.

[89eliminator]

front winch bumper
new rear shock mounts/shocks
rotate rear spring perches just a little to stop my driveline vibe
chop lower rear quarter of bed

now of all that stuff, the only thing that i need done is the bumper. i will still wheel whether or not that other stuff is done.

[GRIMUS99XJ]

I am thinking about adding cage to my list, but time and $ will be the deciding factor on that I am sure.

how about you build a mount for the cheese machine so at every stop we can enjoy a some nachos. It would serve a better purpose the a cage :cheers:

http://rlv.zcache.com/nacho_cheese_and_salsa_hat-p148599050379388056tdto_210.jpg

[XJ&CHZ4ME]

I like your thinking on this...nothing more then a power inverter and a bungee strap :thumbup:

[macgyvr]

I like your thinking on this...nothing more then a power inverter and a bungee strap :thumbup:

you are supposed to be buying a cheese/chili machine and selling me the cheese only machine

mac 'smothered and covered' gyvr

[XJ&CHZ4ME]

10-4, I am still on the look out but too cheap to buy a new one :chef:

[XJ Stryker]

Hope to have my Pop-up camper prior to WF. That is about all I want to get done.

[97XJ2]

Gas skid, fire extinguisher, the fed ex dent will be fixed by the end of the month.

[FlexdXJ]

the fed ex dent

:roflmao: Thats funny. So are the fixing your Jeep or buying you another?

[ILLXJ]

Front shocks--need now
Power steering hose--down the road
Muffler--down the road
Rocker replacement--need now
Alt.--need now
Partial cage--down the road

JIM.

[97XJ2]

:roflmao: Thats funny. So are the fixing your Jeep or buying you another?

Yes, and yes down the road. Yes I'm getting it fixed, but of course I'm still looking for a daily driver with a stick so I can swap parts from the current one (242 n stuff) then I can cage and lift this one more.

Okay, back on topic.

[FlexdXJ]

Yes, and yes down the road. Yes I'm getting it fixed, but of course I'm still looking for a daily driver with a stick so I can swap parts from the current one (242 n stuff) then I can cage and lift this one more.

Okay, back on topic.


Don't blame Ya! I'd like to get a silver 60th as my DD. If i happen to find one after i find a house I just might.

[FlexdXJ]

Well I got some overtime today at work so I am ordering myself a trackbar from IRO. SO i just need to:

install coils
install my JKS disco's
install track bar
install rear shocks
get an alignment
MAYBE buy some 31's
put gas in it
find a hotel room

[seanR]

Jump start battery
Load junk on trailer
Drive to Attica

[POLAR_JEEP_04]

motor rebuilt
new tires
shackle relocaters
permission :)

[cardboard]

Dang it I forgot all about that permission thing! :helpme: Thanx for the reminder, I thought I was done.
Cardboard

[ILLXJ]

Front shocks--need now
Power steering hose--down the road
Muffler--down the road
Rocker replacement--need now
Alt.--need now-----DONE
Partial cage--down the road

JIM.
I think I found my charging problem.
http://i6.photobucket.com/albums/y249/ILLXJ/new/HPIM1910.jpg

JIM.

[FlexdXJ]

I think I found my charging problem.
http://i6.photobucket.com/albums/y249/ILLXJ/new/HPIM1910.jpg

JIM.

Aw, Come on Jim it'll buff out! :D

[XJosh95]

My list:

Get the front end fixed.
Change front axle shaft u-joints.
Install sliders.
Install tow hooks, again.
Weld spare tire carrier to roof rack.
Mount up roof rack.
Budget boost.
Get All-Terrains or better.
Get shocks.
Install D30 diff rock ring.
Get tie rod or my Krusty's track bar.
Install said track bar.
Get Oh-10 Cigars ordered.

[Rev Den]

I think I found my charging problem.
http://i6.photobucket.com/albums/y249/ILLXJ/new/HPIM1910.jpg

JIM.

You have worse luck with castings then anyone I know.

Rev

[IllianaXJ]

Almost forgot; have to wire up the rock lights I installed before WF09 :D

[ILLXJ]

You have worse luck with castings then anyone I know.

Rev

That was an easy fix. 83 Dakota alt. bolts right on. JIM.

[Fore Wheeler]

I'm even working on my junk already. don't know what's wrong with me, it's more than a week away.

[RedHeep]

Build TCase skid
Weld cage to floor
Swap winch bumpers from '91 to '96
Purchase remote for TMax winch
Install CO2 bottle bracket
Build rear tire carrier
Install swaybar (hoping Santa brings an Antirock)
Swap stereo into '96 so the Sirius works
Install CB and tune antenna
Install seats and harnesses (sitting in the kid's bedroom)
Buy another trailer
Drive :)

[SAMSET]

get floors
get lift
get tires
get wheels

i got a ways to go

[FlexdXJ]

get floors
get lift
get tires
get wheels

i got a ways to go

All you really need is a Floor and some rocker protection! Unless there is snow on the ground of course!

[SAMSET]

rocker protection, ha i dont even have rockers

[vincepru]

my list.
-1) buy a wheel and mount my spare
0) cb radio
1) rocker protection
2) fab up a gas tank skid weld it to my hitch
3) find an 8.8 and make it fit.
4) regear to 4.56 or 4.88's
5) ox locker (front or back? cant decide)
6) find a motor for my rear pass side window so i can remove the duct tape

[philagony94xj]

- Install 231 w/SYE
- Raise rear shock mount on axle
- 2x6 Tubing for Rockers
- Mount spare tire bracket on roof rack
............. I'm sure there is more but thats all I can think of right meow.

[poorboy87]

Been working on it. Got the replacement gearbox on the jeep. Got a set of turbine wheels and some used tires. It rides soo smooth now.
Still need to... Get a fullsize spare tire, Find axleshafts for my nondisco axle, swap the non dicsco D30 and replace worn front coils, Towpoints, fire extinguisher, First aid kit, Maybe budget boost

[Coastie]

Get

Front bumper
Winch
Try for a few more months to find a D44 or give up and put in an 8.8
Lock whatever rear axle I go with.
Re-gear 4.88

The last 3 things are really one in the same.

[FlexdXJ]

rocker protection, ha i dont even have rockers

OK fine then get tow points! :laugh3:

[bmyohn]

winch for the front bumper
maybe have a custom AJ rear tire carrier in.
also i may have a CJ-7 to bring along that i hope to buy this spring

[FlexdXJ]

winch for the front bumper
maybe have a custom AJ rear tire carrier in.
also i may have a CJ-7 to bring along that i hope to buy this spring

On that note I need to install my newly acquired(soon to be anyways) ARB bull bar and maybe a winch.

[kastein]

Assuming I find someone to harass into going with me (or for that matter decide to go):
* put new wheels/tires on Jeep, possibly throw a smallish spacer+shackle lift in
* wire up the CB the rest of the way
* build front/rear bumpers...
* drive.
* (non critical) get the OHC and its temp sensor installed, get the SYE done.

EDIT: where do I register, if perchance registration is still open? Assuming I decide to go.

[XJ&CHZ4ME]

I am thinking about installing a new CB after this past weekend, mine simply is a piece of shit.....

[Rev Den]

Registration is not open yet.

Watch here.

Rev

[HaleYes]

We will be looking for someone to make a registration page for us. If you can or know someone willing to help, let myself or a MWC BOD member know.

Registration usually goes up roughly a month and a half (if not a tad earlier) before the event, and usually closes 2 weeks prior.

[REWSTER]

Hope i get a sye or t-case drop so i can make it down there major drive line vibes right now

[99SJ_Ex]

Lift
Tires
SYE (If I have vibes...)

So far, nothing accomplished...

PS. Anyone have some old 31's that are decent, I might be willing to buy em if ya bring em to WF... PM me...

[FlexdXJ]

Bumper is done and I'm ordering my Trackbar, T-case drop and Tie rod within the next couple weeks!

[bmyohn]

Bumper is done and I'm ordering my Trackbar, T-case drop and Tie rod within the next couple weeks!


buy me something while your at it!
:rtm:

[FlexdXJ]

buy me something while your at it!
:rtm:


Says the guy who's rig is already WAYYYYYYY more built than mine! :laugh3:

[XJ&CHZ4ME]

OK, as if I did not have enough going on at home/farm I have taken on a new project. I am going to pick up this weekend a 21' trailer that is a GN and has a small platform over the tongue. It appears to have beena camper of sorts, or the begining of a project at one time that wa abandoned. It has 2x8 main runners and decent cross bracing as well as brakes on the axles. I am going to do my best to reinforce the frame some more and deck it with 4x8 plate steel and then on the upper deck I am going to put plate steel on it and a small railing around it to haul coolers, tires parts etc. Now for teh grand daddy of the project, i am goingto see if I can mount a pop-up camper sideways across the front of the main deck. I know this was done on Xtreme4x4 blah blah blah, but I am doing it in the means of Xtreme Farm Fabrication :farmer: :D The campers are 6'8" and the flat on the trailer is 21', so I should have just enough room on the deck that I can get the XJ and camper mounted up. So, now I need to get it home and start the basic frame supporting and then will move on to decking and then hope to have the camper on it by Winterfest. Wish me luck.....scratch that, I am guided by a force much greater then luck......

Cheeseman-OUT!

[HaleYes]

.scratch that, I am guided by a force much greater then luck......


Yeah, I think I met her at the Pig Gig.

[XJ&CHZ4ME]

haha, that you did! She said it has to be done "sooner then later" b/c she does not want an unfinished project "littering up her property"....somehow I am in the rankings of just the gardner around here now...wish I was the "pool boy" ;)

[XJosh95]

My list:

Get the front end fixed...check.
Change front axle shaft u-joints.
Install sliders.
Install tow hooks, again...check.
Weld spare tire carrier to roof rack...check.
Mount up roof rack...check...
Budget boost.
Get All-Terrains or better.
Get shocks...check.
Install D30 diff rock ring.
Get tie rod or my Krusty's track bar...check.
Install said track bar.
Get Oh-10 Cigars ordered.

Now I have to finish up the other items on the list and add a couple more.
Replace fan clutch assembly.
Install mechanical fan shroud.
Install Z34 hood vents.

[ILLXJ]

Now I have to finish up the other items on the list and add a couple more.
Replace fan clutch assembly.


Get the ZJ HD one, it's only a few dollars more. It's tight getting it in but I think it's well worth it. I'll get a part # for you. JIM.

[Jeeperrick]

I'm going to hate myself for this as it's a lot of work, but...
Making a trip to Iron Rock Off-Road in a few weeks. I just may have a 5.5" long arm kit with me on the way back. Just bought a junkyard Dana 44 out of a waggy...so..

Gears/rear Detroit
rear axle swap
lift
34" LTB's

If I don't do it right away, I'm still fine with my 31" radial swampers and 3" Rough Country lift. I won't take it apart if I can't do it all at once. Sitting out/missing events due to vehicle tear downs sucks!

[XJ&CHZ4ME]

Project "try and make junk ass trailer work and look good" has met its demise already. Upon pulling the trailer out of the brush I looked under it more and the main runners/frame have rust holes through them. Not worth the effort to put into this project..so back to the drawing board. :(

[ILLXJ]

Get the ZJ HD one, it's only a few dollars more. It's tight getting it in but I think it's well worth it. I'll get a part # for you. JIM.


NAPA part# 272310. JIM.

[philagony94xj]

I would suggest AGAINST the HD fan assembly. At least the one that sticks out further towards the radiator. Ask me how I know its a bad idea.

[97XJ2]

Or the factory replacement one from napa with the "radiator death tabs" that stick straight out.

[BRIANHO13]

That would be nice, but I will probably try something like linked and rear steered for wf.......

After this weekend the links are looking more likely.......

[REWSTER]

just bought a whole new jeep to get done by winter fest

[XJ&CHZ4ME]

it can be done...we are finishing a complete XJ makeover for Collin and between it being a stock craptastic rig 2 weeks ago, now it is lifted, has rear disc brakes installed, just received a new paint job and will be getting a few final touches in the coming week. Other then that, a decent build done in 3 weeks. Recruit some good friends and the sky (and your pocket book!) is the limit.....

[FlexdXJ]

Well, Add acquire lights for tail light boxes to my List. Thanks JCR! :D



Rewster..... pics or GTFO! :D

[REWSTER]

Rewster..... pics or GTFO! :D

http://www.cherokeeforum.com/f59/what-did-i-go-do-26897/
here is this for now, i dont feel like starting a new thread :geek:

[XJosh95]

Get the ZJ HD one, it's only a few dollars more. It's tight getting it in but I think it's well worth it. I'll get a part # for you. JIM.

I already have the stocker I pulled at a local salvage yard. Maybe later. I dunno.

[99SJ_Ex]

Got reman distributor installed, next is actually finding/purchasing lift kit... I'm goin 3in with stock tires (till i find some) It'll look goofy... but ohh well....

[FlexdXJ]

Got reman distributor installed, next is actually finding/purchasing lift kit... I'm goin 3in with stock tires (till i find some) It'll look goofy... but ohh well....


Rough country 3 inch series 2 with full packs! Talk to Jason!

[99SJ_Ex]

Rough country 3 inch series 2 with full packs! Talk to Jason!

Unfortunatly it will prob be the Series 1 with add-a-leafs cause I just can't budget that kind of money on the 15hr a week job I have at my college and still pay my bills...

[FlexdXJ]

Unfortunatly it will prob be the Series 1 with add-a-leafs cause I just can't budget that kind of money on the 15hr a week job I have at my college and still pay my bills...

From a guy with AAL's. Save up another 200 bucks and get leafs you'll be much happier!

[XJ&CHZ4ME]

Austin, fire me a PM..I happen to know a guy that knows a guy.....and that guy has the hook up :thumbup:

[AshyLarry]

hope to make my first here. ordering axles, lockers, gears, need to finish limiting straps, new trac bar, and hopefully more

[99SJ_Ex]

Got reman distributor installed, next is actually finding/purchasing lift kit... I'm goin 3in with stock tires (till i find some) It'll look goofy... but ohh well....

Lift Kit purchased
Tires to be picked up
Everything done by end of day November 7th!

(Hopefully a SYE will not be needed...) :dunno:

[FlexdXJ]

Lift Kit purchased
Tires to be picked up
Everything done by end of day November 7th!

(Hopefully a SYE will not be needed...) :dunno:

Right on Austin, What did you end up going with?

[99SJ_Ex]

RC 3in lift with AALs
An awesome fellow Wisconsinite is giving me a deal on 4 31in BFGs with rims, the tires have 7/32 on em which is what my current tires have...
Using my front sway bar links along with some coupler nuts and some key pins to make my own quick disconnects....
Now I just pray I have no drive line vibes....

[FlexdXJ]

RC 3in lift with AALs
An awesome fellow Wisconsinite is giving me a deal on 4 31in BFGs with rims, the tires have 7/32 on em which is what my current tires have...
Using my front sway bar links along with some coupler nuts and some key pins to make my own quick disconnects....
Now I just pray I have no drive line vibes....

Meh you might but a T-case drop, Hack n tap or HD sye will help if not.

[99SJ_Ex]

Well I happen to have acquired an extra t-case and front drive shaft, so something might come of it... hopefully we get to it as needed... If anything, prob do a DIY T-case drop or Hackn tap... Don't have any more funds for a while so no SYE...

[FlexdXJ]

Don't have any more funds for a while so no SYE...

Yeah most of my Jeep fund went to a new pistola today so The trackbar and Tie rod will be it for me for a while.

[cardboard]

:shiver: Wow thats a scary thought Aaron has a gun. :wave1:
Cardboard

[FlexdXJ]

Hell, I've had a rifle for like 3 years. Just now getting a pistol. I'm just preparing for a Zombie invasion! :D

[XJ&CHZ4ME]

hope to get my new JCR 1/4 guards installed by WF...oh, wait, DONE!! :D

[XJ&CHZ4ME]

add to the list...maybe have EXO cage completed. I am picking up an exo cage that was on Reichys rig. It is gonna take some work, but I think I might me able to pull it off. I really wanted an interior cage, but with me being half sasquatch there is not enough room for me and passengers for where the seats need to be and my comfort zone.

[99SJ_Ex]

Update:
Lift and Tires this weekend.

Adding:
Home-made Sway bar extentions and possible quick-disconnect on one end...
Possible DIY SYE... Not sure w\how that will go...

[FlexdXJ]

Update:
Lift and Tires this weekend.

Adding:
Home-made Sway bar extentions and possible quick-disconnect on one end...
Possible DIY SYE... Not sure w\how that will go...

Good luck Austin! I should have my trackbar in a couple weeks so I'll be leveled out finally but most likely still on 235's :(

[99SJ_Ex]

Good luck Austin! I should have my trackbar in a couple weeks so I'll be leveled out finally but most likely still on 235's :(


Yeh I'm gona see where mine sits before I decid to mess with the trac bar...

[IllianaXJ]

Transfer case input shaft bearing, maybe a chain.

Something is making noises in there... been doing it since I put the TeraLow in and recently got worse. Sucks because the TNT crossmember is a biatch to take down.

[HaleYes]

Transfer case input shaft bearing, maybe a chain.

Something is making noises in there... been doing it since I put the TeraLow in and recently got worse. Sucks because the TNT crossmember is a biatch to take down.


Yep. That's why I've not gone with LA's yet.
Just in case my TC bearing goes out.............;)

[XJ&CHZ4ME]

I her ya Byron, I am trying to fab up a unibody stiffiner of sorts and I am dreading taking that TNT belly pan off. It is almost to the point I am, going to build around it :D

[IllianaXJ]

It's almost bad enough for me to wait, try and hock the TNT setup and buy Claytons :D

[XJ&CHZ4ME]

damn, if that is the case, tell me where that money tree is located and it might be worth my drive over there! ;)

[IllianaXJ]

Haha, yeah. I wish.

[FlexdXJ]

Well, I solved my exhaust rattle.........kinda. I got under my Jeep and noticed a shock touching my exhaust. I broke one of the shock bolts and haven't fixedit yet. I guess i probably should huh?

[SDHREDXJ]

more lift Only BB right now
sliders
gas skid
rear disk

[FlexdXJ]

more lift Only BB right now
sliders
gas skid
rear disk

You don't need more lift! You will need sliders though! Disks would help too.

[SDHREDXJ]

my rear is sagging some since they are stock leafs with a lift shackle. I have a set of XJ leafs at home I'm going to make a bastard pack with.

Disks are cause I need to do my rear brakes anyways and might as well upgrade.

[FlexdXJ]

Disks are cause I need to do my rear brakes anyways and might as well upgrade.

Don't blame ya there. I got a line on an 8.8 if i can find somewhere to store it. Just need a 4.10 front axle.

[SDHREDXJ]

yeah a friend, 97XJ2, is checking out a JY by his home where he just got the goods to do rear disk

[ILLXJ]

That was an easy fix. 83 Dakota alt. bolts right on. JIM.

Swapped this one out for a 130 amp. out of a 97 Dodge.
Got some other stuff done:
New taillights & b-ups.
http://i6.photobucket.com/albums/y249/ILLXJ/new/HPIM1930.jpg

Seats.
http://i6.photobucket.com/albums/y249/ILLXJ/new/HPIM1933.jpg

Mounted air tank.
http://i6.photobucket.com/albums/y249/ILLXJ/new/HPIM1929.jpg

Picked up tube for rockers. It's only 1/8 but it should be fine since I'm such a light wheeler.:confused1 And it only cost me $3.
http://i6.photobucket.com/albums/y249/ILLXJ/new/HPIM1932.jpg

JIM.

[ILLXJ]

I also got a room taken care off already.

http://i6.photobucket.com/albums/y249/ILLXJ/new/HPIM1915.jpg

JIM.

[kastein]

One step forward, two steps back!

* throw a smallish spacer+shackle lift in
* trim fenders and install TJ flares
* wire up the CB the rest of the way
* build front/rear bumpers...
* install SYE
* either get regeared or put new axles in (4.10s? 4.56s? 4.88s? hpd30 and 8.25 29sp or 8.8? oh the decisions...)
* drive.

[FlexdXJ]

One step forward, two steps back!

* throw a smallish spacer+shackle lift in
* trim fenders and install TJ flares
* wire up the CB the rest of the way
* build front/rear bumpers...
* install SYE
* either get regeared or put new axles in (4.10s? 4.56s? 4.88s? hpd30 and 8.25 29sp or 8.8? oh the decisions...)
* drive.


You are driving from MA for WF? Hell Yeah!

[kentuckytwostep]

Full width HPD44/9" locked swap.
Flange output parking brake.
35's.

[IllianaXJ]

I also got a room taken care off already.

http://i6.photobucket.com/albums/y249/ILLXJ/new/HPIM1915.jpg

JIM.

Awesome.

[Rev Den]

Jim.....the wife and I slept in one of those once....ONCE. Good thing your skinny.

Like the lights....they won't burn Mikes shirt.

:D

Rev

[ILLXJ]

Jim.....the wife and I slept in one of those once....ONCE. Good thing your skinny.

Like the lights....they won't burn Mikes shirt.

:D

Rev

I figured I'd let Mike sleep in the "double" bed. I'll take the couch. The real reason for getting it is it will be warm. My Uncle uses a small milkhouse heater in it & said at 25 outside it stays around 65 inside with the heater on low.

The lights never burned his shirt on his jeep so they shouldn't on mine. JIM.

[99SJ_Ex]

Lift/tires installed...

Now to figure out how to fix my drive-line vibes... :S

[kastein]

You are driving from MA for WF? Hell Yeah!
Hopefully!

Also, decision on gearing and axle was made... I went to the junkyard and as usual there were no 2.5L XJs. So I went to the Ford Exploder section and yanked an 8.8 with 4.10s out of a C4C vehicle. Now I just need to weld brackets and stuff onto it, get my SYE done (and probably now a custom driveshaft... sigh! add to the list!), and pick up and regear an hpd30 to match - since this is my DD, I'm going to get a new front axle to work on while I drive on my original, then swap em out.

[bmyohn]

Hopefully!

Also, decision on gearing and axle was made... I went to the junkyard and as usual there were no 2.5L XJs. So I went to the Ford Exploder section and yanked an 8.8 with 4.10s out of a C4C vehicle. Now I just need to weld brackets and stuff onto it, get my SYE done (and probably now a custom driveshaft... sigh! add to the list!), and pick up and regear an hpd30 to match - since this is my DD, I'm going to get a new front axle to work on while I drive on my original, then swap em out.


very cool! i think that the week after winterfest i will be driving my XJ from Bloomington, IN out to Amherst, MA to visit some friends and wheel a little bit more! assuming i dont break anything lol

[kastein]

Awesome, swing by Worcester on the way or something. There's a good crew out here, about a dozen guys have shown up for both of the events lobsterdmb has run.

Hope that cruise works for you, IN to MA (and vice versa) is a hell of a trip.

[jester1084]

I have a set of axles begging me to work on them... but the money is still screaming at me. Rear 60 is almost ready to be assembled, all I have left for that is a locker, shafts, install kit, and some other small parts. Front 44 is another story. All I have there is the housing and knuckles. Still need tires then, got some blingin H2 rims already.

[Menzenski]

What I NEED to do:
-buy and install recovery points
-install CB radio
-buy and install fire extinguisher

What I WANT to do:
-swap in new axles with 3.55 gearing (since my 5-speed has 3.07)
-lift it 3"
-mount my 31s
-get skid plates for t-case and gas tank

[kastein]

Man, you guys with the mauals are lucky... your deeper gear ratios are available in any junkyard ever in stock axles...

[FlexdXJ]

OK add to my list a New Jeep! :(

[XJosh95]

Updated list again...Get the front end fixed...check.Change front axle shaft u-joints.Install sliders.Install tow hooks, again...check.Weld spare tire carrier to roof rack...check.Mount up roof rack...check...Budget boost...check...Get All-Terrains or better.Get shocks...check...and installed...check.Install D30 diff rock ring.Get tie rod or my Krusty's track bar...check.Install said track bar...check...Get Oh-10 Cigars ordered. Replace fan clutch assembly...check.Install mechanical fan shroud...check.Install Z34 hood vents. Finish the install on my fog lights...Pull pinch seams straight for sliders...Get the springs and coils from Brendan and put them on...Install T-case drop kit...The list keeps getting longer and longer.
Edit: Install t-case skid coming today.

[XJ Stryker]

Maybe we should have a Wrench fest weekend about a month before Winterfest. Who has the most garage space that could Host?

Thoughts...

[XJ&CHZ4ME]

I have a nice shop that is well stocked w/ tools etc, but I am a bit of a drive for most. The offer is on the table, if anyone wants to have a wrench fest at my shop it is open for the invite. It is heated, plenty of works space for a few rigs at the same time, cold beverages, hot dog machine and nachos are on the house......PM if someone wants to get something going.

Cheeseman-OUT!

[FlexdXJ]

Finish the install on my fog lights...


Why? so you can rip them off in the quarry? :D

[macgyvr]

Maybe we should have a Wrench fest weekend about a month before Winterfest. Who has the most garage space that could Host?

Thoughts...

how about regional wrenchfests? I have a heated garage in Fort Wayne, IN and if I don't have a current project I could get 3 to 4 in here...

mac 'closer than Kansas' gyvr

[FlexdXJ]

how about regional wrenchfests? I have a heated garage in Fort Wayne, IN and if I don't have a current project I could get 3 to 4 in here...

mac 'closer than Kansas' gyvr

Wow thats a Haul there Mac! :eek:

[XJ Stryker]

how about regional wrenchfests? I have a heated garage in Fort Wayne, IN and if I don't have a current project I could get 3 to 4 in here...

mac 'closer than Kansas' gyvr


That is closer than Kansas looks to be about 4-5 hours from me. I would be interested.

Any one is Southern, In lol


XJ 'needs to save gas' Stryker

[XJ&CHZ4ME]

how about regional wrenchfests? I have a heated garage in Fort Wayne, IN and if I don't have a current project I could get 3 to 4 in here...

mac 'closer than Kansas' gyvr

I like that idea Mac. I know that since the MWC is so spread out that one local wrenchfest that is centeralized is still a 8+ hour trip for some members. Anyhooo, my shop is still open for who ever wants to use it.

Cheese "located on the Missouri/Iowa border" Man

[vincepru]

new on my list.

cb radio
rear bumper with tire carrier
sliders
and if i can find one with disks an 8.8 (fingers crossed)

of course, it all depends on how much $ ill have at the time when i find the deals haha

[XJ&CHZ4ME]

we should be able to get to crackin' on that rear bumper in the next week or two....maybe a front bumper as well :dunno:

[vincepru]

hell yeah! just let me know when your up for it. do you know any places around you where i can buy the metal?

[RedHeep]

Build TCase skid
Weld cage to floor
Swap winch bumpers from '91 to '96
Purchase remote for TMax winch
Install CO2 bottle bracket
Build rear tire carrier
Install swaybar (hoping Santa brings an Antirock)
Swap stereo into '96 so the Sirius works
Install CB and tune antenna
Install seats and harnesses (sitting in the kid's bedroom)
Buy another trailer
Drive :)

Front axle seal is leaking
Front inner hub bearings make noise with the hubs locked
Oil pressure gauge still doesn't work right from the swap
Weld frame stiffeners in
Swap my OT gas tank skid in
Move the rear axle back to the last hole on the perches
Install the remote box for my CB, swap the 3 foot antenna and tune
Swap battery cables and ANL fuse box in
Swap yellow top in
Move TMax winch from AJ's bumper to Detours bumper
Install lower door bars and tube from the top to the C-pillar
Shorten the draglink and get an alignment
Weld in front swaybar mounts
Swap Durango steering box in
Replace rear shackles with something shorter
Install front limit straps and bumpstops

Man, the list got longer when I got home and walked around the Jeep for the first time in 6 months. I need to get to work.

[vincepru]

holy crap. that is a long list! so what are you gonna do with the AJ's bumper?

[RedHeep]

It's for sale. See swap meet thread. If I can get the jeep out of the garage today, I'm going to get a picture up for the people who asked for it.

[XJ&CHZ4ME]

hell yeah! just let me know when your up for it. do you know any places around you where i can buy the metal?

empty your PM inbox fool...I can not send you a message.....

[Menzenski]

Well, sold my 31s on Saturday so it looks like I'll be showing up on 235/75R15 all-terrains.

So now my to-do list looks like this:
- finish CB install and tune antenna
- buy and install front tow hooks
- install rear tow hook
- buy and mount fire extinguisher
- put first aid kit and tow strap in Jeep
- re-cover headliner
- buy and install new stereo head unit
- fix what's vibrating at 60-65 mph
- buy and install t-case and gas tank skids (if money allows)

[AshyLarry]

Wire and plumb ARB's
Get rear driveshaft in, when it comes in
Adjust tcase shifter linkage
Get front wheels re balanced
More seat time

[kastein]

the list is growing more than it's shrinking...

figure out what to do about a rear driveshaft once the 8.8 goes in (probably retubing a stock front XJ DS, or maybe an explorer/blazer front DS, have heard those fit)
put the brackets on the 8.8
regear new d30, weld new brackets on new d30
pick up new rims with less backspacing and hopefully new tires (32s or maybe used 33s)
bolt in new axles, install new rear DS, do SYE
get an alignment
bolt the fire extinguisher into the jeep
build and install front bumper with recovery points...
install new seats
finish CB install
run the cabling for my OBA properly so I stop blowing the fuse for my cigarette lighter :gee:

I think that's about it... whew

[RedHeep]

My stock driveshaft fit with my 8.8. I never got around to an SYE. Just put a 1310-1330 joint on the end of it and bolted it to the 8.8 with the ford adapter.

I don't know if you're going to do it all at once or in steps, but your stock one will get you back on the road if you're doing one thing at a time.

[kastein]

Well, I'm hoping to do it all at once - thus why I'm regearing and prepping all the new axles and then installing them. I've got a flange to 1310 adapter sitting on my doorstep right now according to UPS...

Curious, did you switch from a d35 or an 8.25 to an 8.8? And how much lift do you have? All the docs I can find say that a d35 has about 1" shorter pinion than an 8.25 or d44, and an 8.8 apparently has a pinion very close in length to a d35, so I'm just worried that a hack-n-tap SYE on my XJ with 3.5" of lift is going to run out of travel since the shaft is rumored to be ideally sized for an 8.25.

Really, I just need to do the math before I pull the axles.

[RedHeep]

I replaced a D35. It was practically bolt in because the adapter gives you some length.

If you're going to get a new driveshaft, I would wait until you had the new axle in and the SYE done and then measure for the driveshaft. That's the best way to do it and you'll get the right shaft the first time.

[bmyohn]

Added to the list

1) Ford Taurus Electric Fan (my mech. fan is attempting to eat my CSF-3 core radiator)
2) Pull spare shafts from the junkyard.
3) Put gas in and go

[XJosh95]

Added to the list

1) Ford Taurus Electric Fan (my mech. fan is attempting to eat my CSF-3 core radiator)
2) Pull spare shafts from the junkyard.


3) Pull leaf packs and coils from the Up Country you have for XJosh954)Put gas in and go

Fixed it for ya...sorta. My work PC is dumb

[XJosh95]

So, I'm starting to get that "impending doom" feeling that I'm not going to get anything done. I've got a couple months, sure. But, it just feels so cluster-effed that I won't have the time. Anybody else getting that feeling of paranoia?

[XJ&CHZ4ME]

I practically live in a constant state of paranoia...I always have in the back of my head that if I make a royal screw up on the farm I could stand loosing a 5th generation farm and millions of dollars in land, livestock and equipment....so when it comes to the Jeep, I dont sweat it :D

[RedHeep]

So, I'm starting to get that "impending doom" feeling that I'm not going to get anything done. I've got a couple months, sure. But, it just feels so cluster-effed that I won't have the time. Anybody else getting that feeling of paranoia?

If you're not thrashing last minute, you're not doing it right.

[XJ&CHZ4ME]

that is no crap, I was finishing up my long arms last year about 24 hours before departure and Collin literally pulled an all nighter working on his rig and then drove all the way out there (well, all but the last hour where Jerm had to drive b/c Collin started to asleep at the wheel :D)

[BOB]

I practically live in a constant state of paranoia...I always have in the back of my head that if I make a royal screw up on the farm I could stand loosing a 5th generation farm and millions of dollars in land, livestock and equipment....so when it comes to the Jeep, I dont sweat it :D

LOLOL...nothing like a little pressure huh???
:farmer:

BOB

[XJosh95]

All of my adult life I've kinda had the mindset of "If I'm 5 minutes early, I'm on time." Since I've owned a Jeep it seems "If I'm 10 minutes late, I'm ahead of schedule."

[XJ&CHZ4ME]

Josh, that is damn near sig worthy :thumbup:

[RedHeep]

I've got two weeks over christmas to work on the heep with the kids in daycare all day and I'm still going to be doing stuff the weekend prior.

It's just how I am. Sometimes I can spend all day in the garage, sometimes the couch wins.

[XJosh95]

Josh, that is damn near sig worthy :thumbup:

Thanks, Tyler. I suppose I'll just have to wait and see if it shows up anywhere.

[XJ&CHZ4ME]

you may have to look pretty hard for someone that stupid....

[XJosh95]

you may have to look pretty hard for someone that stupid....

Kinda like your wife? (edit: I mean your wife had to look hard for you.) I lol'd when I saw you used it! I appreciate that sentiment.

[XJ&CHZ4ME]

I am still pretty sure she lost a bet w/ her hot friends and that is how she ended up with me...she is a good sport though :D

[HaleYes]

All of my adult life I've kinda had the mindset of "If I'm 5 minutes early, I'm on time." Since I've owned a Jeep it seems "If I'm 10 minutes late, I'm ahead of schedule."

I've not got to that adult part yet.......

[XJosh95]

Wow, thanks, Mr. Obvious. Don't mistake my punctuallity for maturity.

[FlexdXJ]

I hope I get a Jeep by WF, I may go look at a grand on 33's w/ a 5.2 an 90k miles this weekend! :D But I still would rather have a Cherokee!

[XJ&CHZ4ME]

meh...do you like to kiss your cousins also?

[FlexdXJ]

meh...do you like to kiss your cousins also?


If you are talking about me No! I was just kidding about the ZJ. It is decent but who do you think I am, Brad?! :D

[ILLXJ]

meh...do you like to kiss your cousins also?

Kinda depends on the cousin don't it.:smootch: JIM.

[XJ&CHZ4ME]

it does...he just has to be really hot for Aaron I guess :D

[BOB]

I am thinking about tackling a wiring mess.
I have a remote fuse box for accesories,\.
some wires here, some there....
I may want to do this now in a garage than on the trail.
Is anybody familiar with any wiring gurus near the west burbs????

BOB

[FlexdXJ]

it does...he just has to be really hot for Aaron I guess :D

Dude, were talking Really really hot for me to even consider it. I'll just take my chances with your sister! :D

[XJosh95]

:thumbup:Yup!

[vincepru]

looks like something broke in the transfer case today when i hit some snow and pulled the lever :( now i gatta see what i can do to fix that. sounds like there is a machine gun shooting at my belly pan when i put it in full time and give it half throttle.

[macgyvr]

i guess i need to replace a trailer tire on the 2-place before winterfest...

http://i215.photobucket.com/albums/cc74/macgyvr/new%20trailer/downsized_1207091923.jpg

mac 'no wonder there was a vibration' gyvr

[99SJ_Ex]

Mac - That'll be fine... Long as there's no holes, its still good! :D

tEx

[RedHeep]

i guess i need to replace a trailer tire on the 2-place before winterfest...

http://i215.photobucket.com/albums/cc74/macgyvr/new%20trailer/downsized_1207091923.jpg

mac 'no wonder there was a vibration' gyvr

Already? The damn things are practically brand new.

[Rev Den]

Vince...

Could be ujoints....but they usually click
Could be a chain slipping.

What year? Disconnect D-30?

Rev

[vincepru]

rev i have a 98 with the 242

[RedHeep]

Already? The damn things are practically brand new.

Couldn't see the pic at work.

Looks maybe heat related from under inflation. What are you running them at?

[macgyvr]

Couldn't see the pic at work.

Looks maybe heat related from under inflation. What are you running them at?

i know the cause...

I ran over the sewer grate in my yard trying to get off the street with wet ground...came in to hot to control...caught the grate and busted a belt...with 14k pounds...had to unload the two jeeps and then could move it with an empty trailer...

i think that i justified the two place redheep...i used it btw 6 to 8 times this year...

mac 'least i didn't hit the fire hydrant' gyvr

[Rev Den]

Vince....sorry man, dont know much about the 242. Try posting in the OEM Forum and see what you get.

If the joints check out OK, I am gonna say something in the case.

Rev

[vincepru]

Vince....sorry man, dont know much about the 242. Try posting in the OEM Forum and see what you get.

If the joints check out OK, I am gonna say something in the case.

Rev


just got it back from the shop. they said the joints were fried, rear axle (d35) is about to blow, and the T case chain is slipping bad and i need a new transfer case... :doh:

[IllianaXJ]

2nd opinion.

[vincepru]

2nd opinion.
as in take it somewhere else to get looked at?

[FlexdXJ]

as in take it somewhere else to get looked at?

Yeah I believe thats what he meant. Of course the D35 is gonna blow they came that way from the factory! :D

[vincepru]

Yeah I believe thats what he meant. Of course the D35 is gonna blow they came that way from the factory! :D

the D35 isnt what worries me :P thats just giving me more motivation to swap something better in!

however im skeptical that the tcase is actually bad, because ive never had an issue with it before, and i really havent beat on my rig for something like a chain to start slipping in it. when i got the SYE installed everything seemed ok in there, and it never gave me problems before. spoke to tyler about it, he said it could be my linkage that got messed up and it wont engage all the way. i will inspect it further once it warms up a bit.

[XJ&CHZ4ME]

Vince, I think I have a t-case found for ya if you need one. I am supposed to hear back today from the guy. I need to do a little research on the 242 for years of compatability. I will give ya a ring later today....

[vincepru]

Vince, I think I have a t-case found for ya if you need one. I am supposed to hear back today from the guy. I need to do a little research on the 242 for years of compatability. I will give ya a ring later today....

right on man! i just wish i could take a look inside to see whats really wrong with it, i would hate to waste money on a part that doesnt need replacing.

[IllianaXJ]

Pop your linkage off of the t'case shift lever. Manually shift the case into Full Time and try to drive it. If it works fine, adjust your linkage to match. If not, stick a fork in it.

[vincepru]

didnt think of that. thanks ill try that today!

[RedHeep]

i know the cause...

I ran over the sewer grate in my yard trying to get off the street with wet ground...came in to hot to control...caught the grate and busted a belt...with 14k pounds...had to unload the two jeeps and then could move it with an empty trailer...

i think that i justified the two place redheep...i used it btw 6 to 8 times this year...

mac 'least i didn't hit the fire hydrant' gyvr

It definitely makes you popular if you have other guys to wheel with.

I was never going to tow two vehicles again.

You still hate the bumper pull? It does leave your bed open.

[vincepru]

didnt think of that. thanks ill try that today!

messed with the linkage today. def not it, problem is inside :tear:

anything that would be an upgrade for the 242? i figured if im gonna spend a couple hundred on a tcase, i can see if i can just put a beefier one in it instead of the 242.

[macgyvr]

It definitely makes you popular if you have other guys to wheel with.

I was never going to tow two vehicles again.

You still hate the bumper pull? It does leave your bed open.

i wouldn't say that I hate bumper pull...just not a big fan...it works, and it was affordable, i actually prefer to tow bumper pull because i think its more predictable than gooseneck...that said i've done lots more bumper pullin than i have gooseneck pullin...

two weekends ago i had the 2 place out and a buddy borrowed my single place and we all went to the badlands...

mac 'bed is still open for a truck camper :) 'gyvr

[IllianaXJ]

messed with the linkage today. def not it, problem is inside :tear:

anything that would be an upgrade for the 242? i figured if im gonna spend a couple hundred on a tcase, i can see if i can just put a beefier one in it instead of the 242.

I would just find a JY replacement and drop it in. Since you are working with a 242, you can't upgrade to a TeraLow. An Atlas would be $$. A 241 would take some fab work, but would be an option.

[vincepru]

I would just find a JY replacement and drop it in. Since you are working with a 242, you can't upgrade to a TeraLow. An Atlas would be $$. A 241 would take some fab work, but would be an option.

yeah atlas is wayyy over my spending range. i think a used 242 is the best bet i guess. although i have to pull out my SYE and swap it, no idea how to do it (had a shop "on and off road" in ohio do it)

[Rev Den]

Just a thought, what about replacing it with a 231?

Might be cheaper in the long run.

Rev

[vincepru]

Just a thought, what about replacing it with a 231?

Might be cheaper in the long run.

Rev

i really know nothing about the 231 tcase other than i would not have 4wheel part time anymore and i would have to buy a new SYE, which i cannot afford since the one in there is practically brand new

[IllianaXJ]

A SYE swap would be pretty easy, as long as the output shaft is ok. If you're close to Tyler, I'm sure he would help you out.

Shop around on the classifieds, other forums (JF, JU, etc). You may find a 231 equipped with a SYE for around the same price as a stock 231/242.

[BIGSLVRXJ]

that is no crap, I was finishing up my long arms last year about 24 hours before departure and Collin literally pulled an all nighter working on his rig and then drove all the way out there (well, all but the last hour where Jerm had to drive b/c Collin started to asleep at the wheel :D)
That was good stuff. I'm going to hope the same doesn't happen this year. Sleep is NOT overrated before an all day road trip...

[Rev Den]

i really know nothing about the 231 tcase other than i would not have 4wheel part time anymore and i would have to buy a new SYE, which i cannot afford since the one in there is practically brand new

Actually...you would lose full-time 4X4. The 231 is a part time case.

Rev

[vincepru]

A SYE swap would be pretty easy, as long as the output shaft is ok. If you're close to Tyler, I'm sure he would help you out.

Shop around on the classifieds, other forums (JF, JU, etc). You may find a 231 equipped with a SYE for around the same price as a stock 231/242.

yeah we were planning on building a rear bumper and swingout, but now it looks like were gonna have to figure out how to do the SYE. hes never done it on a 242 and ive never touched my tcase or anything before so i have no idea whats going on in there.

[XJ&CHZ4ME]

I cant see it being much different then doing a 231, and I have done about a half dozen of those...:dunno:

[RedHeep]

The 242 and the 231 are identical at the output shaft.

[XJ&CHZ4ME]

thanks Josh, I was think thinking that they might be, so 91 up should work for him. I am hoping that he gets another case and I will just help him swap the SYE over to it and get that taken care of and we will throw a 8.25 in the back as well and hopefully he will be Winterfest bound before we know it!

[vincepru]

oh you can bet that i will be there this winterfest! and with a very capable tip top xj. marked on the calendar and ive already started a WF fund haha

[XJ&CHZ4ME]

add another $35 bucks to that fund and go RED!! :D all the cool kids are doing it :thumbup:

[vincepru]

add another $35 bucks to that fund and go RED!! :D all the cool kids are doing it :thumbup:
you know whats funny, i always plan on going red, but whenever i get that $ in my pocket somehow the jeep knows it and breaks something new :roll:

but hey, with christmas coming up im sure ill have no problem going red. maybe ill put a membership on my list haha

[RedHeep]

you know whats funny, i always plan on going red, but whenever i get that $ in my pocket somehow the jeep knows it and breaks something new :roll:

but hey, with christmas coming up im sure ill have no problem going red. maybe ill put a membership on my list haha

Don't overdue yourself.

It's not like there's a great big message board here with a bunch of folks trying to help you. The internet is free :doh:

[vincepru]

Don't overdue yourself.

It's not like there's a great big message board here with a bunch of folks trying to help you. The internet is free :doh:

i realize that its excuse after excuse, but right now that 35$ goes a long way for me (unemployed college student). but ill be going red soon

[FlexdXJ]

I need to A.) get the Beater ready for WF or B.) Get the soon to be DD ready for WF! :D

[poorboy87]

Gearbox replacement, Motormounts replaced, Oil leaks repared, Different tires, all done.

need tow points, fire extinguisher, spare tire and first aid kit

[99SJ_Ex]

Find electrical drain on system and eliminate it... Install some noise suppressors on main electrical lines... My previous list...

[ILLXJ]

Gearbox replacement, Motormounts replaced, Oil leaks repared, Different tires, all done.

need tow points, fire extinguisher, spare tire and first aid kit

What size spare do you need? JIM.

[poorboy87]

Im on 225/75 15s. I need a wheel and tire. Id like to find another turbine like I got. What you got?

[ILLXJ]

I know I don't have a turbine rim,plenty of steelies. Might be able to come up with a 225 or 235. Let me check around. JIM.

[vincepru]

i have 4 30" BFG AT's in my garage that would be great for trail spares, lots of tread left. anybody needs one lemme know!

[poorboy87]

I know I don't have a turbine rim,plenty of steelies. Might be able to come up with a 225 or 235. Let me check around. JIM.


Thanks Jim

[RedHeep]

What does a turbine wheel look like?

Nevermind. If you would have said 10 spoke, I would have got it.

All I have is a set of limited wheels that have been painted gray.

[XJosh95]

Last night I managed to get my front diff guard on along with my RC X-Flex LCAs. Still a list of things to do. XJosh-Knocking them out bit by bit-95

[FlexdXJ]

Last night I managed to get my front diff guard on along with my RC X-Flex LCAs. Still a list of things to do. XJosh-Knocking them out bit by bit-95

:yelclap: you fixing mine next? :D

[XJosh95]

:yelclap: you fixing mine next? :D

If Brad gets his ZJ out of his garage by New Years and you manage to get it up there, you might find me willing for the brown paper bag fee. You know what comes in brown paper bags, and you know what to put in it for me. I'll see what the possibilities are, but first you have to tell me everything that's wrong with it. Other than the obvious loose nut behind the wheel.

[FlexdXJ]

but first you have to tell me everything that's wrong with it. What isn't wrong with it? :D

[ILLXJ]

This last week I replaced:
X-fer case rear output seal.
High pressure power steering line.
Drivers side motor mount.

Also finished up my Brothers "shop", just have to clean it up a little, then I can get the Jeep inside where it's nice & warm. JIM.

[XJosh95]

What isn't wrong with it? :D

The four letters on the front?

[95' heep]

hope to make some cage made and a good snorkel system made (into the cowl) and a OBA and a organization system made, and fix all of the bugs out of the XJ.

[XJ&CHZ4ME]

I might add getting a kidney and liver transplant to my list of things to get done..I want to have a good & fresh set before this years festivities b/c I know what I did to my current set last year :D :cheers:

[REWSTER]

i have 4 30" BFG AT's in my garage that would be great for trail spares, lots of tread left. anybody needs one lemme know!



free or realy cheep? :D


just looking for a spare

[vincepru]

free or realy cheep? :D


just looking for a spare

as of now tyler has dibs on them. ill be bringing them to WF on a trailer, and if he doesnt want them after he checks them out, they will be in the possession of the first person who hands me a freshly opened beer :cheers:

[XJosh95]

Adding to my list of crap to get done...Aussie in the D30. The locker is sitting on my kitchen counter, looking sad and lonely.

[kastein]

man... still gotta do almost everything! :twak:

dunno if I'm gonna make it. At least my rear axle is nearly built, and my front axle is done except for gears and a little more bracing on an LCA bracket.

[FlexdXJ]

OK, I'll start my list over!

Install hitch
Install THB's(or sell my beater and get bumpers to take care of tow points)
Rework and install sliders
install CB

[cardboard]

What do you want for the beater.

[FlexdXJ]

$800 OBO, I have a thread in the FS section.

[cardboard]

bring it by here when you get that skid.

[FlexdXJ]

bring it by here when you get that skid.

I can probably do that. Gonna go get the new one plated tomorrow so I may swing by tomorrow.

[cardboard]

OK see you Wedesday evening.

[FlexdXJ]

Right on I'll be there.

[IllianaXJ]

They have these things called PMs you guys :D



I still have to get my XJ in the shop. Gonna have to drop the @#$%^!*%$ TNT crossmember and pull the trans; I'm thinking the flexplate is cracked or loose.

[REWSTER]

i got a T-case skid that i need to put on, also want to find a gas tank skid so i dont pop my plastic tank on a rock or something, want to get some lights for my roof rack but that wont matter

im sure other things will pop up within 7 months

I Have done nothing :dunno:




as of now tyler has dibs on them. ill be bringing them to WF on a trailer, and if he doesnt want them after he checks them out, they will be in the possession of the first person who hands me a freshly opened beer :cheers:

cool, i shall have a beer on hand somewhere :cheers:

[RedHeep]

Put my trailer order in. That's one thing off the list.

http://www.kaufmantrailers.com/heavy-equipment-trailer-store/Single-Car-Haulers/16-Ft,-7,000-lb.-Diamond-Single-Car-Hauler-p63.html

[discosteve]

i gotta fix a front end noise. and help poorboy87 with the buget boost if he gets one.

[XJ&CHZ4ME]

gotta add to my list-fix upper rear shock mounts...maybe a custom fabbed up BPE set up. Last night we were chasing cattle in the XJ and I heard a popping the back, the shock busted loose at the top..again. Thining I am gonna reinforce the new welded in slider/rockers as well...

[FlexdXJ]

Put my trailer order in. That's one thing off the list.

http://www.kaufmantrailers.com/heavy-equipment-trailer-store/Single-Car-Haulers/16-Ft,-7,000-lb.-Diamond-Single-Car-Hauler-p63.html

Thats not a bad price for that trailer!

[RedHeep]

Thats not a bad price for that trailer!

Factory direct. The factory is in Lexington, NC and I'm picking it up on the way back from vacation in Asheville.

They ship to dealers nationwide, but then you pay the markup.

[RedHeep]

Just ordered my swaybar kit.

The list is growing.

[RedHeep]

Front axle seal is leaking
Front inner hub bearings make noise with the hubs locked
Oil pressure gauge still doesn't work right from the swap
Weld frame stiffeners in
Swap my OT gas tank skid in
Move the rear axle back to the last hole on the perches
Install the remote box for my CB, swap the 3 foot antenna and tune
Swap battery cables and ANL fuse box in
Swap yellow top in
Move TMax winch from AJ's bumper to Detours bumper
Install lower door bars and tube from the top to the C-pillar
Shorten the draglink and get an alignment
Weld in front swaybar mounts
Swap Durango steering box in
Replace rear shackles with something shorter
Install front limit straps and bumpstops

Man, the list got longer when I got home and walked around the Jeep for the first time in 6 months. I need to get to work.

Draglink is done. Took 1/2" out of it, got the steering wheel centered and the trackbar put back to the right length. I'm still up against it with the rod ends, but I think it will be ok. Turns a lot better now. I need to get it on an alignment machine and check the numbers. I have very little return to center.

Shackle boxes are sitting in the living room. Going to take off the boomerang shackles and use the RE ones on the '91.

Tomorrow the front hubs come apart for grease and servicing and I'm going to get the axle moved back. It's nice working in a clean garage for a change.

[95' heep]

Heres a list I WANT to do before the WF

-Spare tire on a correct backspaced rim
-get rid of the D35 for a 8.25 OR Ford 8.8
-get doors back on it
-fix the battery parasitic draw
-install a cheap cb
-hood pins
-snorkel made into the cowl
-remove and discard the rear seats
-raise the gas tank and build a sort of a spare tire holder on top of that along small boxes made on the sides if there's any room to allow
-make a orgazation in place where the rear seat originally went for my tools, spare driveshafts, axle shafts, cooler, etc etc
-redo the rock sliders for cage
-OBA using the A/C compressor
-redo the front bumper for the cage
-build a cage!

so far in the progress..

-a 8.25 should be coming in in near future
-hood pins kit purchased
-one side of the rock sliders is in the progress
-i have my hand on a set of doors, but dont have them yet, hopefully soon

needs more tubes and right diesets for the bender for the tubes then i can actually make some good progress

[vincepru]

my main goals to get done before wf.

fix all the tranny problems, change all fluids.
buy 4.88 gears, and an aussie for the rear.
find a way to secure my 33" spare somewhere, be it rear tire carrier/ roof rack/ or somehow secure it in the trunk.
if i get lucky and find some at a cheaper price, install sliders and a gas tank skid.

the thing im most excited about though, my girlfriend said she would go half and half with me on a roof top tent for the xj :D

[chaz_88_MJ]

Will be ordering 4.88's for the heep and installing the 8.8 in the next few weeks. As usuall waiting until the last minute to do anything...haha It will proabably come down to the night before until everything gets done...lol

[REWSTER]

i got my t-case drop and skid plate on over the weekend, thanks to the weekend wheelers group (philagony94x and beez1989)

now i want to trim my fenders and throw my hood pins on

[philagony94xj]

i got my t-case drop and skid plate on over the weekend, thanks to the weekend wheelers group (philagony94x and beez1989)

now i want to trim my fenders and throw my hood pins on

Glad everything went well and no "major" issues. I guess having a handy dandy camera scope helps out huh? :D Hey, and any excuse to get out the grinder to do some fender trimming, I'm game! Muah ha ha ha ha.....

[GoSlowGetStuck]

I found out last year: make your WF to-do list, cut it in half, then cut it in half again because there's just not enough time to get it all done. :(

Spent the past month or so pulling everything off the motor to put on new heads (old ones overheated and warped), change gaskets, new radiator, etc. Everything is done now but the exhaust. So...
- load Jeep on trailer, go to exhaust shop for exhaust fab work
- change transmission pan gasket and filter
- swap NP249 out for NP231 w/ SYE, hope I don't botch that up
- put in order to RC for lift kit (was going to use junkyard springs and hack it together but time is running out) and wait for it to arrive
- break bolts, curse, drink beer, regain composure, install lift

My only optional to-do is throwing a locker in the crap Dana 35. An 8.8 was on the original list, but see my note about cutting the list in half twice :D

Addendum: based on my 1 year of WF experience, the only thing I *NEED* to do is buy a few cases of beer, some frozen turkeys, show up, and find an open seat!